| TI: | Measurement of Wall-Thickness at Extreme Temperatures Using EMATs |
| AU: | Kroening, M.; Salzburger, H.-J.; Von Bernus, L.; Smorodinski, Y.; Mironenko, V. |
| SO: | Nair, K.; Raj, B.; Murthy, C.L.; Jayakumar, T. (Ed.) 14th World Conference on Non-Destructive Testing 1996. Vol. 1 New Delhi: Oxford & IBH Publishing, 1996, S.577-580 Conference: World Conference on Non-Destructive Testing <14, 1996, New Delhi> ISBN 81-204-1122-6 |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | Electromagnetic Acoustic Transducers (EMAT) can be applied for temperatures ranging from very low minus numbers up to 1000 deg C. Reasons are the couplant free excitation of the ultrasound in the materials itself and a possible assembly of the probe without adhesives. Moreover using EMATs temperature changes of the specimens in the range below Curie-point do not affect significantly the calibration setting; they can also be used for technical surfaces with paint scalings of other thin coatings. But the practical use of EMAT is limited because of equipment costs and minor accuracy of measurement results are due to poor signal characteristics compared with established techniques based on piezo-electric transducers. A new EMAT instrument for wall-thickness measurement is presented. Special emphasis was put on the design of the transducer and the preamplifier to get precise data of high resolution. |
| UT: | Corrosion; electromagnetic-acoustic-transducer; high-temperature; Hochtemperatur; Korrosion; nondestructive testing; Signal analysis; Ultraschall; ultrasound; wall thickness measurement; Wanddickenmessung; zerstoerungsfreie Pruefung |
| AV: | IZFP |
| SM: | F-0-334.A; F-0-334.A(2); F-0-334.A(3) |
| ED: | 97/11/14 |
| TI: | Miniaturisierung und Erhoehung des Frequenzbereiches von EMUS-Winkelpruefkoepfen durch Einsatz von Hochfrequenz-Uebertragern |
| AT: | Miniaturization and increase of the frequency range of EMUS-angle probes using RF-cores |
| AU: | Salzburger, H.-J.; Huebschen, G. |
| SO: | Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung e.V. -DGZfP-, Berlin Die ZfP der DACH-Laender im Spiegelbild internationaler Normung. Band 2 Berlin: DGZfP, 1996, S.533-540 (DGZfP-Berichtsbaende, 52,2) Conference: Jahrestagung Zerstoerungsfreie Materialpruefung <1996, Lindau> ISBN 3-931381-07-0 |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | EMUS-Angle Probes Consisting of Permanentmagnets with spatially alternating polarity have been successfully used as T/R probes (seperate transmitter T and receiver R) for Shear Horizontal waves in the frequency range >1 Mhz. To increase the frequency range and to reduce the geometrical size of the probes, the RF air coils of the probe were replaced by RF coils wounded on high permeable RF cores. By the approach as well the stronger efficiency losses due to lift-off effects at frequencies > 1 Mhz as due to weaker magnetization strength could be compensated. Moreover it was possible to reduce the geometrical size of the probes because of the possibility to use the same RF core as transmitter and receiver. |
| UT: | angle beam probe; EMUS; Phased Array; shear wave; Transversalwelle; Ultraschall; ultrasound; Winkelpruefkopf |
| AV: | IZFP |
| SM: | F-0-284.12B |
| ED: | 97/09/26 |
| TI: | Tiefenbestimmung von Laufflaechenfehlern an Eisenbahnraedern unter Nutzung linearer polarisierter Transversalwellen. Verfahrens-Optimierung und Erprobung |
| AT: | Detection and sizing of cracklike defects in the tread of railway wheels by linearly polarized ultrasonic shear waves. Technique and equipment |
| AU: | Salzburger, H.-J.; Hintze, H. |
| SO: | Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung e.V. -DGZfP-, Berlin Die ZfP der DACH-Laender im Spiegelbild internationaler Normung. Band 1 Berlin: DGZfP, 1996, S.167-174 (DGZfP-Berichtsbaende, 52,1) Conference: Jahrestagung Zerstoerungsfreie Materialpruefung <1996, Lindau> ISBN 3-931381-07-0 |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Modern rail traffic is characterized by continuous increase of speed and operation hours of the vehicles. Rails and especially the wheels underlie high load which can result in surface breaking cracks in the tread of the wheel. By routine nondestructive inspection checks the forming of cracks is controlled. Once a crack in the tread has been detected its depth is of most interest first due to safety considerations and second due to economical aspects. Detection and Sizing are done by an ultrasonic technique under insonification of linearly polarized shear waves in normal direction into the tyre transmitted and received by a couplant free Electromagnetic Acoustic Transducer (EMAT). The direction of the poloarization is parallel to the direction of circumference. Amplitude and phase of the echoes of the opposite face of the tyre (backwall echoes) are evaluated. If there is a cracklike defect within the sound field of the transducer amplitude and phase of the echo are changed due to a mod e conversion of the incident linearaly polarized shear wave into a rayleigh wave propagating along the flanks of the crack. By scanning the transducer in radial direction of the wheel and recording amplitude and phase of the backwall echo the depth of the crack is determined. |
| UT: | crack; Eisenbahnrad; Modemumwandlung; Polarisation; polarization; railway wheel; Riss; Ultraschall; ultrasound |
| AV: | IZFP |
| SM: | F-0-284-12A |
| ED: | 97/09/26 |
| TI: | Trockene Ultraschall-Pruefung von Reaktorkomponenten mittels EMUS. Potential, Nachweisempfindlichkeiten und Pruefkonzept |
| AT: | Dry ultrasonic testing of reactor components by EMUS. Potential, sensivity for detection, conception of an inspection scheme |
| AU: | Salzburger, H.-J.; Huebschen, G.; Kroening, M. |
| SO: | Univ. Stuttgart, Staatliche Materialpruefungsanstalt -MPA- Sicherheit und Verfuegbarkeit in der Anlagentechnik mit dem Schwerpunkt Komponenten nuklearer und konventioneller Kraftwerke. Bd. 2. Vortraege 31-54 Stuttgart: MPA, 1996, S.48.1-48.10 (MPA-Seminar, 22) Conference: Materialpruefungsanstalt (Seminar) <22, 1996, Stuttgart> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | It has been shown that on principle a dry ultrasonic inspection of thickwalled primary circuit components of nuclear power plants is possible using EMUS-probes. Investigations on test specimens have demonstrated that the inspection area sprescribed by regulations can be covered by SH-waves and the postulated sensitivity of detection for cracklike defects can be reached. |
| UT: | defect analysis; dry ultrasonic inspection; electromagnetic ultrasonic probe; elektromagnetische Ultraschallwandlung; EMUS; Fehleranalyse; trockene Ultraschallpruefung |
| AV: | IZFP |
| TI: | Erarbeitung prueftechnischer Grundlagen fuer den regelwerksgerechten Einsatz der Ultraschall-Pruefung von Misch- und austenitischen Schweissnaehten mit horizontal polarisierten Transversalwellen (SH-Wellen) und ElektroMagnetischen UltraSchall (EMUS)-Pruefkoepfen. Vortrag. |
| AT: | Acquisition of basic rules for the standardization of the ultrasonic inspection of bimetallic and austenitic welds using horizontally polarized shear waves (SH-waves) and electro magnetic ultra sonic (EMUS)-probes |
| AU: | Salzburger, H.J.; Huebschen, G.; Kroening, M.; Hesselmann, W. |
| SO: | Univ. Stuttgart, Fakultaet 5 Energietechnik, Staatliche Materialpruefungsanstalt -MPA- 21. MPA-Seminar '95. Sicherheit und Verfuegbarkeit in der Anlagetechnik mit dem Schwerpunkt Massnahmen zur Absicherung des Langzeitbetriebs von Kernkraftwerken. Bd.1 Stuttgart: 1995, 15 S. Conference: MPA-Seminar <21, 1995, Stuttgart> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Die Arbeiten haben die moeglichen Einsatzbereiche der EMUS-Technik und die zu beruecksichtigenden Worst-Case Bedingungen festgelgt. Anhand orientierender Labor-Untersuchungen unter den festgelegten Worst-Case Bedingungen wurden die Einsatz-Moeglichkeiten ermittelt. Die wesentlichsten Pruefkopfdaten sind esperimentell und theoretisch insbesondere unter Beruecksichtigung der vorkommenden Wanddicken und Rohrdurchmesser erfasst worden und koennen zur Erstellung von Pruefkopfdatenblaettern herangezogen werden. Grundempfindlichkeit, Nutkennlinien, Empfindlichkeitszonen und Signal/Rauschabstaende von Kalibrier- und Bezugsreflektoren wurden ermittelt. An ausgewaehlten Testkoerpern im vereinbarten Druchmesser- und Wanddickenbereich wurden Vergleichsmessungen mit den Standardtechniken durchgefuehrt. |
| UT: | electromagnetic ultrasound transduction; elektromagnetische Ultraschallwandlung (EMUS); EMUS-Pruefkopf; Pruefkopf |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Koppelmittelfreie Ultraschallwandlung mit elektromagnetischen Pruefkoepfen - Anwendung und Potential in der zerstoerungsfreien Prueftechnik |
| AU: | Salzburger, H.J. |
| SO: | Arnold, W.; Hirsekorn, S. (Ed.) Deutsche Gesellschaft fuer Akustik -DAGA-, Oldenburg Fortschritte der Akustik - DAGA '95. Tl.1. Plenarvortraege und Kurzreferate Oldenburg: 1995, S.7-11 Conference: Deutsche Jahrestagung fuer Akustik <21, 1995, Saarbruecken> ISBN 3-9804568-0-3 |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Die ElektroMagnetische (EMUS)-Wandlung ist eine Technologie zum koppelmittelfreien und quasi beruehrungslosen Senden und Empfangen von Ultraschall. Einen umfasesenden Einblick in Aufbau, Funktionsprinzip und Anwendungen der EMUS-Technologie bieten Uebersichtsartikel von R.B. Thompson et al. und H.M. Frost. Die EMUS-Technologie kennzeichnet sich dadurch aus, dass die Ultraschallwandlung im Pruefobjekt stattfindet und die Kopplung zwischen Pruefkopf und Pruefobjekt ueber elastomagnetische Felder erfolgt. Dadurch unterscheidet sie sich elementar von der piezoelektrischen Wandlungstechnik. Gemeinsam haben beide Techniken, dass Sende- und Empfangs-Wandlung auf reziproken Effekten beruhen und damit in einem Sende-/Empfangs-Pruefkopf realisiert werden. Damit bestehen bei der EMUS-Technik keine grundsaetzlichen Unterschiede zur Piezo-Technik bezgl. der Prueftechniken (Impulsecho, Durchschallung, Laufzeitverfahren, Resonanzverfahren etc.). Aehnliches gilt auch bzgl. des grundsaetzlichen Aufbaus und der Fun ktionsweise der zugehoerigen Pruef- und Messelektronik. |
| AV: | IZFP |
| SM: | A-3-160.A |
| ED: | 97/09/26 |
| TI: | The capability and application of horizontally polarised shear waves for the ultrasonic inspection of austenitic welds |
| AT: | Capacit‚ et Application des Ondes de Cisaillement ... Polarisation Horizontale pour le Contorle Ultrasonore des Soudures Austenitiques |
| AU: | Bohler, R.V.; Shipp, R.; Huebschen, G. |
| SO: | Comite Europeen sur les Essais Non Destructifs -ECNDT-, Paris 6th European Conference on Non-Destructive Testing '94. Vol.2 Paris: 1994, S.851-855 Conference: European Conference on Non-Destructive Testing <6, 1994, Nizza> |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | Nuclear electric's NDT applications Centre, in collaboration with IzfP, Germany, has evaluated Electromagnetic Acoustic Trasnducers (EMATs) for the generation of horizontally polarized shear (SH) waves for ultrasonic inspection of austenitic welds. A range of austenitic weld blocks containing both realistic and artificial defects have been inspected using both angle compression wave probes and EMATs. The comparison shows that SH wave results have good signal to noise ratio for the detection of defects and the SH wave images are much "cleaner" than those for angel compression waves simplifying data interpretation. Modelling is used to explain the observed phenomena and to predict cases where SH waves might be best employed and where SH waves offer no significant benfit over compression waves. The paper discusses the benefits and drawbacks of using EMATs compared with angle compression wave probes and proposes inspection strategies incorporating both probe types. |
| UT: | austenitic weld; electromagnetic-acoustic transducer; ultrasonic inspection |
| AV: | IZFP |
| SM: | F-0-308.B |
| ED: | 97/09/26 |
| TI: | Electromagnetic ultrasonic (EMUS) probes: state of the art and developments for application in nuclear power plants |
| AU: | Salzburger, H.J.; Kroening, M.; Huebschen, G. |
| SO: | Iida, K.; Whittle, J.M. (Ed.) American Society for Metals -ASM-, Metals Park/Ohio; British Institute of Nondestructive Testing 12th International Conference on NDE in the nuclear and pressure vessels industries Metals Park/Ohio: 1994, S.137-142 Conference: International Conference on NDE in the Nuclear and Pressure Vessels Industries <12, 1994> ISBN 0-87170-506-0 |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | The excitation and detection of ultrasound by conventional piezoelectric techniques doesn't provide the full range of elastic wave modes which can be used for NDT. Besides this there is a limitation of the temperature range. This gap can be filled up using alternative techniques for the ultrasonic transduction. One of the most far developed alternative techniques is the electromagnetic ultrasonic (EMUS) excitation and detection. EMUS-probes work free of liquid couplants; hence they can be appplied for inspection and measurements at higher temperatures. The transduction of shear waves with horizontal polarization (SH-)waves can be more reliably performed by EMUS-probes for practical applications than by piezoelectric shear wave transducers using Y-cut quartzes. The contribution presents the performance of phased-array angle-probes. The application of these probe-type for the ISI of austenitic and dissimilar welds using SH-waves will be shortly highlighted. For the continous monitoring o f the liquid level in the vessel of BWR's from outside at temperatures of 300øC SV-wave angle probes are used. Their performance for operation in the mentioned temperature range and the principle of measurement of the liquid level will be described. Ongoing development work to enlarge the frequency range of EMUS-probes and for the automatic control of the lift-off will be shortly described. |
| UT: | austenitic weld; austenitische Schweissnaht; EMUS; filling level; SH-wave; shear horizontal wave; Ultraschall |
| AV: | IZFP |
| SM: | F-0-260.9 |
| ED: | 97/09/26 |
| TI: | Progress in UT of austenitic and dissimilar metal welds using Shear Horizontal Waves and Electromagnetic US -EMUS- probes |
| AT: | Fortschritte der Ultraschallpruefung austenitischer und Misch-Schweissnaehte unter Nutzung von horizontal polarisierten Transversalwellen und EMUS-Pruefkoepfen |
| AU: | Kroening, M.; Huebschen, G.; Salzburger, H.J. |
| SO: | EPRI NDE Center EPRI pipe inspection workshop. Sess. 2 Charlotte/N.C.: 1993 Conference: Workshop on Pipe Inspection <3, 1993, Charlotte/N.C.> |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | Among the different ultrsonic wave modes - Longitudinal (L-) waves, Shear waves with polarization in the plane of incidence (SV-waves), L-waves with a high beam angle of 70 (TRL 70) and SH-waves show most promising advantages for the inspection of austenitic and dissimilar metal welds. Whereas high beam angle L-waves excited and detected by conventional piezoelectric probe-technology and equipments have been used for some years, for the application of SH-waves appropriate EMUS-probes and instrumentations had to be developed. The contribution will describe the basic physical features of SH-waves contributing to the improvement of the inspectability of welds with dendritic grain structure. The experimental verification of their theoretically predicted capability to penetrate into the weld and to pass trough the wild will be demonstrated by results of automated test specimen-measurements. Apart from this, the design of the EMUS-probes and -instrumentations will be presented. Phased-Array probes with up to 8 array elements and electronically steerable beam angles from 90 to 40 angle were developed; the realization of the instrumentation for in-field applications will be described. |
| UT: | austenitic weld; austenitische Schweissnaht; dissimilar metal; electromagnetic ultrasonic probe; elektromagnetische Ultraschallwandlung; EMUS; Mischnaht; SH-wave; SH-Welle; Ultraschallpruefung; ultrasonic testing |
| AV: | IZFP |
| SM: | F-0-301 |
| ED: | 97/09/26 |
| TI: | Results and experiences of ISI austenitic and dissimilar welds using SH-waves and EMUS-probes |
| AU: | Salzburger, H.J.; Bernus, L. von; Oellrich, K.; Huebschen, G.; Kroening, M. |
| SO: | Bundesanstalt fuer Materialforschung und -pruefung -BAM-, Berlin Structural mechanics in reactor technology. SMIRT. Vol.4. Part G. Reactor pressure vessels Berlin: 1993, S.249-254 Conference: International Conference on Structural Mechanics in Reactor Technology (SMIRT) <12, 1993, Stuttgart> |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | Increasing demands for In-Service-Inspection (ISI) of austenitc and dissimilar metal welds in NPP's in Germany and other european countries from the motivation of the application of new NDE-techniques with potential to improve the inspectability of these types of welds. In this context also the requirements of the german code KTA 3201.4 (revision 6.1990) of ultrasonic inspection of dissimilar metal welds has to be considered. Up to now in the most cases standar and special UT-techniques are only covering the HAZ's ; to fulfill the code requirements the inspection has to be performed from both sides of the weld. Dissimilar metal welds are in many cases only accessible from one side. Therefore US-techniques are necessary which are capable to inspect the whole weld even if there is only access from one side. Among the different ultrasonic wave modes - Longitudinal (L-) waves, Shear waves with polarization in the plane of incidence (Sv-waves) and Shear waves with polarization perpendicula to the plane of incidence (SH-waves), Sh-waves show most promising advantages for the inspection for longitudinal defects in austenitic and dissimilar metal welds, as was demonstrated in different cases. |
| UT: | austenit; longitudinal wave; Longitudinalwelle; nondestructive testing; shear horizontal wave; shear wave; Ultraschallpruefung; Ultraschallwelle |
| AV: | IZFP |
| SM: | E-8-32 |
| ED: | 97/09/26 |
| TI: | Ultraschallpruefung von austenitischen und Mischschweissverbindungen mit SH-Wellen und EMUS-Pruefkoepfen |
| AU: | Hoegberg, K.; Eriksson, H.; Huebschen, G.; Salzburger, H.J. |
| SO: | Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung e.V. -DGZfP-, Berlin 60 Jahre DGZfP - Erfahrungen und Nutzen fuer Europa. Teil 1 Berlin: 1993, S.241-248 (DGZfP-Berichtsbaende, 37) Conference: Zerstoerungsfreie Materialpruefung <1993, Garmisch-Partenkirchen> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Among the different ultrsonic wave modes - Longitudinal (L-) waves, Shear wves wiht polarization in the plane of incidence (SV-waves) and Shear waves with polarization perpendicular to the plane of incidence (SH-waves), L-waves with a high beam angle of 70 (TRL 70) and SH-waves show most promising advantages for the inspection of austenitic and dissmilar metal welds. Whereas high beam angle L-waves excited and detected by conventional piezoelectric probe-technology and equipments have been used for some years, for the application of SH-waves appropriate EMUS-probes and instrumentations had to be developed. The contribution will describe the design of EMUS-probes and equipments. The experimental verification of the theoretically predicted capability of SH-waves to penetrate into the weld and to pass through the weld will be demonstrated by results of automated test specimen-measurements. The EMUS-Sh-wave technique has been successfully applied in several swedish muclear power pants. |
| UT: | austenitic weld; austenitische Schweissnaht; dissimilar metal; electromagnetic ultrasonic probe; elektromagnetische Ultraschallwandlung; EMUS; Mischnaht; SH-wave; SH-Welle; Ultraschallpruefung; ultrasonic testing |
| AV: | IZFP |
| SM: | F-0-284.9A |
| ED: | 97/09/26 |
| TI: | Untersuchungen zum Einfluss von ferritischen Phasen in austenitischen Schweissnaehten auf die Schallfeldvermessung mit elektromagnetischen Sonden |
| AU: | Walte, F.; Schurig, C.; Kretzschmar, F. |
| SO: | Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung e.V. -DGZfP-, Berlin 60 Jahre DGZfP - Erfahrungen und Nutzen fuer Europa. Teil 2 Berlin: 1993, S.652-658 (DGZfP-Berichtsbaende, 37) Conference: Zerstoerungsfreie Materialpruefung <1993, Garmisch-Partenkirchen> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | The propagation of elastic waves in anisotropic material like austeniic welds is at present one of the major targets in the field of ultrasonic basic physics. To verify the theoretical predictions often ultrasonic through tranmission experiments ar conducted where by teh transmissions amplitude is received using a point like electromagnetic-acoustic tranducer. The contend of delta ferritic phases in austenitic welds influences the sensitivity of electromagnetic-acoustic transducers (EMAT's) and led to a misinterpretation of experimental results. Using a laser influence is quantitative estimated and in addition componed with measurements using piezoelectric transducers |
| UT: | austenitic weld; electromagnetic-acoustic-transducer; laser interferometer; Ultraschall; ultrasound; wave propagation; Wellenausbreitung |
| AV: | IZFP |
| SM: | F-0-284.9B |
| ED: | 97/09/26 |
| TI: | New EC- and UT-systems for the in-service-inspection of austenitic and dissimilar weldmentsat elevated temperatures |
| AT: | Neue Wirbelstrom- und Ultraschallsysteme fuer die wiederkehrende Pruefung austenitischer und Misch-Schweissnaehte bei erhoehten Temperaturen |
| AU: | Salzburger, H.J.; Becker, R.; Huebschen, G. |
| SO: | Vereinigung der Technischen Ueberwachungs-Vereine e.V. -VdTUeV-, Essen Pressure vessel technology 1992. Vol.2. Materials manufacturing, quality Duesseldorf: 1992, S.1289-1302 Conference: International Conference on Pressure Vessel Technology <7, 1992, Duesseldorf> |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | The described EC-inspection system works with four frequencies (30kHz-2MHz) simultaneously fed into the inspection coil. The mixing of the resulting measuring signals is otimized to characterize and to size fatigue and corrosion cracks in austenitic weldments. To solve this task it is necessary to suppress the disturbing conditions growing from the coil lift-off. The applied sensors are designed for an elevated temperature (250xC). For the inspection of the inner near surface zone of the two circumferential welds HORIZONTALLY POLARIZED SHEAR (SH)-waves, excited and detected by EMUS-probes, are used. The probes are optimized to fulfill htree different inspection functions and are designed to operate at 150xC. SH-waves are used because of their ability for gracing incidence and their advantageous features for the inspection of anisotropic abd coarse grained dissimilar welds. |
| UT: | eddy current testing; elastic wave; Kernreaktor; Mehrfrequenz; Nondestructive testing; nuclear power station; Polarisation; Schneller Brueter; Schweissnaht; shear wave; Transversalwelle; Ultraschall; ultrasonic materials testing; welding; Wirbelstrom; zerstoerungsfreie Pruefung |
| AV: | IZFP |
| SM: | 92013 |
| ED: | 97/09/26 |
| ND: | 11428 |
| TI: | EMUS-Geraetetechnik - Stand, Anwendungen, Entwicklungstendenzen |
| AU: | Huebschen, G.; Neuschwander, R.; Salzburger, H.J.; Wilbrand, A. |
| SO: | Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung e.V. -DGZfP-, Berlin Innovative ZfP - eine Herausforderung fuer die gesamte Industrie. Teil 2 Berlin: 1992, S.596-603 (DGZfP-Berichtsbaende, 33) Conference: Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung (Jahrestagung) <1992, Fulda> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | The state of the art of the EMUS (electromagnetic-ultrasonic) system technology is illustrated presenting as examples two typical systems, an 8-channel phase array system for ultrasonic inspections in the field especially of the primary circuit of nuclear power plants, and a 2-channel standard system. The phased array technique provides a significant enhacement of the signal-to-noise ratio and the bandwidth, suppression of the sensitivity in the backward direction of the ultrasonic probe, and allows electronic setting and changing of the angle of incidence at a fixed frequency. Production costs of EMUS systems will be reduced by modular design of all electronic components. Miniaturization using SMD and PAL technology will alow to build e.g. a 8-channel phased array system housing with a height of 150 mm. Miniaturized EMUS probes allow new applications of the EMUS technique utilizing Rayleigh waves, shear horizontal waves, and normally incident linearly polarized shear waves. |
| UT: | 1992; Eisenbahn; electromagnetic transduction; elektromagnetische Ultraschallwandlung; filling level; Fuellstand; high-speed train; high-temperature probe; Hochgeschwindigkeitszug; Hochtemperaturpruefkopf; inservice inspection; inspection system; modular system; modulares System; monitoring; Oberflaechenpruefung; Pruefsystem; railway wheel; railways; Rohr; surface inspection; tube; Ueberwachung; Ultraschall; Ultraschallgeraet; Ultraschallpruefkopf; Ultraschallpruefung; ultrasonic equipment; ultrasonic materials testing |
| AV: | IZFP |
| SM: | 92027 |
| ED: | 97/09/26 |
| TI: | Frueherkennung von Kriechschaeden - Zum Stand fortschrittlicher Zerstoerungsfreier Pruefverfahren |
| AU: | Dobmann, G.; Koble, T.D.; Kroening, M.; Willems, H. |
| SO: | Technische Vereinigung der Grosskraftwerksbetreiber e.V. -VGB-, Essen Restlebensdauer 1992 Essen: 1992, S.21.1-21.11 Conference: Restlebensdauer <1992, Mannheim> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | The contribution refers results for the development and application of nondestructive testing techniques for the early detection of creep damage on the box of the development of creep cavitation, porosity and micro cracking. Beside ultrasonic phase velocity measurements electromagnetic techniques have been investigated at creep test specimen of different steels as well as at pipe bends. Whereas the electromagnetic techniques and derived quantities for materials state characterization (Barkhausen noies, coercivity, magnetic distortion factor, electrical resistivity) follow very sensitive the temperature and load induced microstructure changes in the steels the ultrasonic phase velocity changes are strongly affected by creep cavitation, i.e. creep damage. The detectability starts when oriented creep pores occur in the component near surface zones. Ultrasonic surface waves are the relevant tool, excited by piezoelectric and received by EMAT - transducers. |
| UT: | creep; damage; early detection; electrical conductivity; elektrische Leitfaehigkeit; Frueherkennung; Kriechen; magnetic inspection; magnetisches Pruefverfahren; Schaedigung; Schallgeschwindigkeit; sound speed |
| AV: | IZFP |
| SM: | 92039 |
| ED: | 97/09/26 |
| TI: | Materials characterization using electromagnetic ultrasonic -EMUS- transducers |
| AU: | Salzburger, H.J. |
| SO: | Institution of Electrical Engineers -IEE-, London IEE Colloquium on NDT 1992 - Non-Destructive Testing in the Single European Market London: 1992, S.2/1-2/4 Conference: Colloquium on Non-Destructive Testing <1992, London> |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | UT by electromagnetic transducers - state of technology and applications in industry |
| AU: | Hoeller, P.; Salzburger, H.J. |
| SO: | Monitoring, Surveillance, and Predictive Maintenance of Plants and Structures 1992, S.50-57 Conference: International Conference on Monitoring, Surveillance, and Predictive Maintenance of Plants and Structures <1992, Firenze> |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | Electromagnetic Ultrasonic (EMUS) testing systems are now ready for being used for a wide spectrum of industrial testing problems which can be solved much better by EMUS-techniques than by conventional piezoelectric techniques. Under the main headlines +quality assurance (QS) during fabrication +pre-service inspection +in-service-surveillance during operation examples are presented : Hot inspection during fabrication of steel products (CC-slabs), ISI of the treas of railways wheels, ISI of austenitic welds, dissimilar welds and cladding. Continuous surveillance from outside of the water level in BWR-vessels at operation temperatures, texture analysis of cold rolled strips. |
| UT: | 1992; Defect; quality assurance; Residual stress |
| AV: | IZFP |
| SM: | 92007 |
| ED: | 97/09/26 |
| TI: | Defect characterization with advanced NDE methods |
| AU: | Brinette, R.; Deuster, G. |
| SO: | The European Journal of Nondestructive Testing 1 (1991), Nr.2, S.59-63 |
| DT: | Journal |
| LA: | en |
| CC: | 03.25 |
| AB: | In the framework of the German Reactor Safety Programme, as well as many large nuclear components, three full-scale pressure vessels areavailable. With them, the capability of modified and newly-developed NDE techniques has been demonstrated under in-situ conditions. It is shown how different techniques such as ultrasonics, potential drop and acoustic emission can detect and characterise various defect configurations. |
| UT: | 1991; ALOK; EMUS; Fehlerbeschreibung; Grossbehaelter; HDR; LSAFT; Phased Array; Potentialsondenverfahren; Riss; Risswachstum; Schallemissionspruefung; Thermoschock; Wirbelstromverfahren |
| AV: | IZFP |
| SM: | 91047 |
| ED: | 97/09/26 |
| TI: | Electromagnetic acoustic transducers |
| AU: | Alers, G.; Maxfield, B.; Repplinger, W.; Thompson, B.; Wilbrand, A.; Huebschen, G.; Salzburger, H.J. |
| SO: | American Society for Nondestructive Testing -ASNT-, Columbus/Ohio Ultrasonic Testing 1991, S.326-340 |
| DT: | Article |
| LA: | en |
| CC: | 03.25 |
| AB: | The electromagnetic acoustic transducers (EMAT) is a device for the excitation and detection of ultrasonic waves in conductive or magnetic materials. No physical contact is required with the test object because the coupling occurs through electromagnetic forces. The working distances are typically less than a milimeter and the probe often is alowed to rest on the surface of the test object. This ability to provide reproducible signals with no couplant is often more important than noncontact operation. |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Weiter-Entwicklungen und praktische Anwendungen der EMUS-Technik |
| AU: | Huebschen, G.; Kroening, M.; Salzburger, H.J. |
| SO: | Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung e.V. -DGZfP-, Berlin DACH-Jahrestagung 1991. Zerstoerungsfreie Materialpruefung. Teil 2 Berlin: 1991, S.506-513 (DGZfP-Berichtsbaende, 28) Conference: Zerstoerungsfreie Materialpruefung <1992, Luzern> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Die elektromagnetische Ultraschall (EMUS)-Wandlung hat sich in den letzten Jahren als eine fuer viele praktische Anwendungen geeignete Technik erwiesen. Unterschiedliche Pruef- und Messverfahren wurden damit realisiert. Zwischenzeitliche Weiter-Entwicklungen des Hochfrequenzteils der Pruefkoepfe haben dazu gefuehrt, dass die notwendigen Vormagnetisierungs-Induktionsdichten um den Faktor 2-3 niedriger sind als bei EMUS-Pruefkoepfen mit "konventionellem" HF-Teil bei vergleichbarer Schall-Intensitaet. Da diese Indiktondichten bereits mit kleinvolumigen Permanent-Magneten erreicht werden, konnten sehr kompakte, verschleissarme Pruefkopf-Ausfuehrungen realisiert werden. Dies eroeffnet eine Reihe von neuen Anwendungen. Es werden der grundsaetzliche Aufbau dieser Pruefkoepfe beschrieben und deren Vor- und Nachtiele gegenueber konventionellen EMUS-Wandlern aufgezeigt. Die spezifische Eigenschaften und die sich daraus ergebenden praktischen Anwendungen werden vorgestellt: -Warmfester Aufbau zum Einsatz bei erhoeh ten Temperaturen bis ca. 300 Grad Celsius ohne Kuehlung zur Kontrolle des Fuellstandes in Behaeltern und Rohrleitungen. -Sehr geringes Pruefkopfvolumen und verschleissarme Ausfuehrung zum Einsatz an komplizierten Geometrien (Schienen) und zur Innenpruefung von Rohrleitungen. -Mehrpruefkopf-Anordnungen zur flaechendeckenden Pruefung von Oberflaechen (Grobblechen). -Erweiterter Frequenzbereich fuer Oberflaechenwellen zur Charakterisierung von oberflaechennahen Kriechschaeden ueber US-Geschwindigkeitsmessung. |
| UT: | 1991; elektromagnetische Ultraschallwandlung (EMUS); EMUS-Pruefkopf; Innenpruefung; Rohrleitung; zerstoerungsfreie Pruefung |
| AV: | IZFP |
| SM: | 91035 |
| ED: | 97/09/26 |
| TI: | Defect characterization with advanced methods |
| AU: | Brinette, R.; Deuster, G. |
| SO: | Iida, K.; Whittle, J.M. (Ed.) American Society for Metals -ASM-, Metals Park/Ohio; British Institute of Nondestructive Testing 10th International Conference on NDE in the Nuclear and Pressure Vessels Industries Metals Park/Ohio: 1990, S.747-757 Conference: International Conference on NDE in the Nuclear and Pressure Vessels Industries <10, 1990, Glasgow> ISBN 0-87170-506-0 |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | In the framework of the German reactor safety program besides larger nuclear components three pressure vessels in 1:1 scale are available. The capability of different refined and new developed NDE techniques is demonstrated under in-situ conditions. It will be shown how different techniques as ultrasonics and electromagnetics as well acoustic emission can detect res. analyse the various defects configurations. |
| UT: | ALOK; EMUS; Fehlerinterpretation; Fehlernachweis; HDR-Sicherheitsprogramm; MPA-Grossbehaelter; PISC II; Riss; SAFT; Schallemission; Schweissnahtfehler; Thermoschock |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Detection of corrosive defects in bottom plates of gas and oil tanks using guided ultrasonic waves and electromagnetic ultrasonic -EMUS-transducers |
| AU: | Huebschen, G.; Salzburger, H.J. |
| SO: | 9th European Congres on Corrosion. Vol.2 1990, S.1-217 Conference: European Congress on Corrosion <9, 1989, Utrecht> |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | Guided ultrasonic waves can detect corrosion in bottom plates of tanks and are capable to inspect latge areas. Couplant free EMUS probes allow an inspection without careful cleaning of the surface. Probes and ultrasonic tenchique have a big potential for a faster and cheaper inspection. |
| UT: | abtragende Korrosion; elektromagnetische Ultraschallwandlung; gefuehrte Ultraschallwelle; horizontal polarisierte Transversal-Moden; Rohrleitung; Taukboden; Ultraschall; Wanddicken-Verringerung |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Monitoring the filling level of the RPV using stationary EMUS-probes |
| AU: | Loehr, E.; Walleser, A.; Huebschen, G. |
| SO: | Nuclear Engineering and Design 119 (1990), S.456-466 ISSN 0029-5493 |
| DT: | Journal |
| LA: | en |
| CC: | 03.25 |
| AB: | Today the filling level in the reactor pressure vessels (RPV) of a boiling water reactor is measured exclusively by the approved differential pressure method based on a comparison of columns of weights. Because of the high importance which the filling level in the RPV respresents for the safety of a nuclear power plant, a physically diverse measuring method has been searched for which satisfies the following requirements: -unequivocal signal generation, - sufficient precision, -good time behavior, -possibilty of installation in existing plants. A binary working ultrasonic method, with which discrete marks of the filling level in the RPV can be surveyed, fulfils these requirements. (-z-) |
| UT: | component; EMUS; reactor pressure vessel |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | UT with SH-waves and electromagnetic ultrasonic -EMUS-transducers |
| AU: | Huebschen, G. |
| SO: | Review of Progress in Quantitative Nondestructive Evaluation. 9B New York: Plenum Publishing, 1990, S.815-822 (Review of Progress in Quantitative Nondestructive Evaluation, 9B) Conference: Annual Review of Progress in Quantitative Nondestructive Evaluation <16, 1989, Brunswick> |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | In the ultrasonic testing practice of today SV- and longitudinal waves are exclusively used becuse these wave types can be excited by piezoelectric ultrasonic transducers introduced a long, time ago. SH-waves offer a number of advantages compared to SV- and longitudinal waves as for example: - reflection, refraction and diffraction without mode conversion, - complete corner reflection independent of the angle of incidence, - propagation in thick-walled components (d bigger than lambda) as a bulk wave even along the surface, - propagation in thin-walled components (d smaller or equal than lambda) as a guided wave (SH-mode), - no radiation of energy into fluids of small viscosity. In principle it is possible to excite SH-waves by piezoelectric transducers, but in practice these transducers are not applicable due to coupling problems. |
| UT: | austenitic cladding; austenitic weld; bottom plate of tank; corrosion; EMUS-transducer; SH-wave; surface inspection; ultrasound |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | ALOK-imaging and -reconstruction of surface defects on heavy plates with E.M.A.-Rayleigh wave transducers |
| AU: | Rieder, H.; Salzburger, H.J. |
| SO: | Review of Progress in Quantitative Nondestructive Evaluation. 8A New York: Plenum Publishing, 1989, S.1127-1135 (Review of Progress in Quantitative Nondestructive Evaluation, 8A) Conference: Annual Review of Progress in Quantitative Nondestructive Evaluation <15, 1989, La Jolla/Calif.> ISBN 0-306-42837-7 |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | High quality heavy plates have to be free of any defects. The UT-inspection for internal defects is introduced as a standard. However, until now the inspection for surface defects is limited to visual inspection, magnetic stray flux - or eddy current inspection. The most sensitive technique is the magnetic stray-flux technique, but it is very time consuming because of the necessity to scan the whole surface. Using Rayleigh waves the inspection can be automated and performed at rolling speed. The sensitivity of frequency optimized Rayleigh waves is sufficient to detect a 0.3mm deep model defect at a distance of 300mm. The use of piezoelectric probes is limited by coupling problems. These problems are overcome by the use of EMAT's, which have been optimized with respect to probe size, sensitivity and wear resistance. For the automated inspection the ALOK-system has been adapted in a laboratory system to the surface inspection of heavy plates by Rayleigh waves. This equipment consisits of an ultrasonic hardware device for fast data-acquisition and-preprocessing (essential data reduction) according to the ALOK-algorithm, and a computer to realize noise- and ghost- elimination as well as defect imaging and -reconstruction. Examples of the surface inspection of heavy plates using electromagnetically excited Rayleigh waves in connection with the ALOK data-acquisition and evaluation system are reported. The investigations were supported by the ECSC (European Community for Steal and Coal). |
| UT: | ALOK; defect imaging; defect reconstruction; EMAT; heavy plate; Rayleigh-wave; surface inspection |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Automatische wiederkehrende Ultraschallpruefung der Laufflaechen von Hochgeschwindigkeits-Schienenfahrzeugen |
| AT: | Automated ultrasonic-in-service-inspection of the tread of high-speed-railway-wheels |
| AU: | Schmidt, W.; Salzburger, H.J. |
| SO: | Schmidt, G.; Steusloff, H. (Ed.) Mit vernetzten, intelligenten Komponenten zu leistungsfaehigeren Mess- und Automatisierungssystemen Muenchen: Oldenbourg, 1989, S.124-133 Conference: Interkama <11, 1989, Duesseldorf> ISBN 3-486-21323-7 |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Using Electro-Magnetic-Ultrasonic (EMUS)-probes the tread of railway wheels is nondestructively inspected for surface defects. The ultrasonic probe is a part of a multi-sensor-system controlling the automatized inspection-procedure. The inspection is performed while the railway wheels are in motion. The inspection data are preprocessed by a my-computer to a protocol containing relevant information on the condition of the tread. This information can be transferred via an interface to the repair workshops. |
| UT: | EMUS; inspection system; offener Steuerkreis; open control circuit; Pruefsystem; Radlaufflaeche; Rayleigh-wave; Rayleigh-Welle; Schienenfahrzeug; technical diagnosis; technische Diagnose; Ultraschall; ultrasound; wheel tread |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Elektromagnetischer Ultraschallpruefkopf fuer die Oberflaechenpruefung bei Temperaturen bis 1000 Grad Celsius |
| AU: | Smit, H.; Wilbrand, A. |
| SO: | Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung e.V. -DGZfP-, Berlin Moderne ZfP - Analysen und Prognosen Berlin/West: 1989, S.460-467 Conference: Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung (Jahrestagung) <1989, Kiel> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Es wird der Laborprototyp eines elektromagnetischen Ultraschallpruefkopfs fuer die Oberflaechenpruefung bei hohen Temperaturen vorgestellt. Der Pruefkopf besteht aus - einem wassergekuehlten Elektromagneten zur Erzeugung eines horizontalen Magnetfeldes mit einer Flussdichte von 0,4 T in paramagnetischem Material bei einer elektrischen Leistungsaufnahme von 5,5 kW (36.000 Amperewindungen) - einem fokussierenden HF-Spulensystem aus 2 Sende- und 2 Empfangsspulen mit Unterdrueckung der Rueckwaertsrichtung (Prueffrequenz rund 250 kHz) - einem zweikanaligen rauscharmen Vorverstaerker - einem Druckluft-Kuehlsystem fuer den Vorverstaerker und die HF-Spulen. Der Pruefkopf wurde im Labor in Kalt- und Heissversuchen an ca. 0,5 x 0,5 qm grossen Proben aus Stahl-Stranggussbrammen mit Oszillationsmarken bei Probentemperaturen bis ca. 1050 Grad C erprobt. Sowohl eine funkenerodierte Nut von 10 mm Laenge und 1 mm Tiefe in einer 850 Grad C heissen Brammenprobe aus ferritischem Stahl wurden mit einem elektrischen Signal/Rau sch-Verhaeltnis von 20 dB und mehr nachgewiesen. Insbesondere wurden damit erstmals natuerliche Fehler in Stahl oberhalb der Curil-Temperatur mit elektromagnetisch Tangeregten Rayleighwellen nachgewiesen. Von seiner thermischen Standfestigkeit her kann der Pruefkopf bei Oberflaechentemperaturen bis mindestens 1050 Grad C eingesetzt werden. |
| UT: | Bramme; elektromagnetische Ultraschallwandlung; EMUS; Hochtemperatur; Oberflaeche; Oberflaechenfehler; Oberflaechenriss; Rayleigh-Welle; Stahl; Stahlguss; Strangguss; Ultraschall; Ultraschallpruefkopf; Ultraschallwelle |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | EMUS-systems for stress and texture evaluation by ultrasound |
| AU: | Huebschen, G.; Repplinger, W.; Salzburger, H.J.; Wilbrand, A. |
| SO: | Hoeller, P. (Ed.) Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung e.V. -DGZfP-, Berlin Nondestructive Characterization of Materials III Berlin/West: Springer, 1989, S.681-690 Conference: International Symposium on Nondestructive Characterization of Materials <3, 1988, Saarbruecken> ISBN 3-540-51856-8 |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | Methods for the evaluation of stress and texture by time-of-flight measurements of ultrasonic waves use of a broad variety of wave types, which include normally incident shear waves and compressional waves, Rayleigh waves, Lamb modes and SH modes. Under field condition, the only means for the excitation of normally incident shear waves and SH modes is to use an electromagnetic-ultrasonic (EMUS) system. Apart from this such a type of ultrasonic system provides a high degree of reproducibility and allows high scanning speeds. These features have led to the development of several EMUS probes for applications to time-of-flight measurements and of transmit/receive-electronics with a high power solid-state transmitter stage. The probes include a small permanent magnet probe for linearly polarized shear waves, a transducer with a water-cooled electromagnet for the simultaneous exictation of orthogonally polarized shear in turbine axles, and a combined piezoelectric/EMUS probe for the simultan eous excitation of compressional waves and shear waves in screws also at elevated temperatures up to 150 degree C. EMUS transducers for Lamb and SH modes in plates have also been applied to time-of-flight measurements aiming at texture evaluation. The different probes will be described, and their performance including the electronical system will be discussed. All probes provide good accuracy for the time-of-flight measurements (up to 3 x 10 high minus 5). |
| UT: | Eigenspannung; elektromagnetische Ultraschallwandlung; Kaltband; Lastspannung; Pruefkopf; Schweissnaht; Textur; Turbinenwelle; Ultraschall; Ultraschallaufzeitmessung; Walzblech |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Entwicklung eines koppelmittelfreien Ultraschall-Pruefsystems zur wiederkehrenden Pruefung des innenoberflaechennahen Bereichs der Tankschweissnaehte 1 und 6 des SNR 300 |
| AU: | Huebschen, G.; Salzburger, H.J. |
| SO: | Jahrestagung Kerntechnik, Bonn, INFORUM 1989, S.467-470 Conference: Kerntechnik <1989, Duesseldorf> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Fuer die Ergaenzung der zur Zeit vorgegebenen wiederkehrenden Pruefungen am Reaktortank des KKW-Kalkar - im wesentlichen optische Inspektion mit Fernsehkameras - wird ein zerstoerungsfreies Pruefverfahren auf Ultraschallbasis entwickelt und qualifiziert, das eine zerstoerungsfreie Pruefung des innenoberflaechennahen Bereichs der Tankwand im Bereich der Rundachweissnaehte 1 (ferritische Naht) und 6 (ungepufferte Mischnaht zwischen dem ferritischen und austenitischen Teil des Behaelters) ermoeglichen soll. Diese Entwicklung wird vom BMFT gefoerdert und in enger Zusammenarbeit und Abstimmung mit der Firma Interatom und einem Manipulato-Hersteller durchgefuehrt. Die vorliegende Pruefaufgabe verlangt den Einsatz von Ultraschallwellen, die die Oberflaeche und den oberflaechennahen Bereich erfassen. Dazu gehoeren neben den Rayleighwellen die streifend eingeschallten, tangential polarisierten Transversalwellen (SH-Wellen). Diese werden an der Trennflaeche Grundmaterial/Schweissgut einer austenitischen oder Misch- Schweissnaht durch Impedanzanpassung zu 100% in das Schweissgut uebertragen werden, was von wesentlicher Bedeutung fuer die Pruefbarkeit ist. Das Senden und Empfangen dieser Wellen muss auf koppelmittelfreie Art und Weise erfolgen, da an der Innenoberflaeche mit Natriumresten zu rechnen ist. Mit Hilfe der elektromagnetischen Ultraschall(EMUS)-Technologie werden die fuer die Oberflaechenpruefung der Schweissnaehte besonders gut geeigneten SH-Wellen effektiv und koppelmittelfrei angeregt und empfangen. Die Umbegungsbedingungen - Temperatur und Strahlenbelastung - sind bei EMUS-Pruefkoepfen durch Einsatz entsprechender temperatur- und strahlungsbestaendiger Materialien beherrschbar. Es wird ueber Ergebnisse zur Laengs- und Querfehlerpruefung berichtet. |
| UT: | EMUS; Mischnaht; Oberflaechenpruefung; SH-Welle; SNR 300; Warmpruefkopf |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Erste Betriebserfahrungen mit einem EMUS-System zur Fuellstandskontrolle am RDB |
| AT: | First operating experiences with an EMUS-system for monitoring the filling level of a RPV |
| AU: | Loehr, E.; Oed, R.; Huebschen, G. |
| SO: | Univ. Stuttgart, Fakultaet 5 Energietechnik, Staatliche Materialpruefungsanstalt -MPA- 15. MPA-Seminar '89. Sicherheit und Verfuegbarkeit in der Anlagentechnik mit dem Schwerpunkt Langzeitintegritaet der druckfuehrenden Bauteile von Kernkraftwerken Stuttgart: 1989, S.20.1-20.19 Conference: MPA-Seminar <15, 1989, Stuttgart> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Anlaesslich des MPA-Seminars 1988 wurde ueber Ergebnisse von Laboruntersuchungen zur Methode der Fuellstandskontrolle am RDB mit Ultraschall berichtet. Es wird mittels EMUS-Sonden, die fuer eine Umgebungstemperatur von 300 Grad C ausgelegt sind, eine Transversalwelle an der RDB-Aussenwand unter einem Winkel von 40 Grad in die Behaelterwand eingeschallt. Durch Ausnutzung der ins Wasser gebrochenen Longitudinalwelle wird ein Echosingnal von einem Einbauteil (z.B. der Trocknerschuerze) empfangen. Ist kein Wasser vorhanden, kann das Reflektorecho nicht mehr detektiert werden. Dieses Reflektorecho ist nur auswertbar bis zu einem Luftblasenanteil von etwa 1 Vol%. Bei hoeheren Luftblasenanteilen wird die unterschiedliche Schwaechung der sich zickzackfoermig in der Behaelterwand ausbreitenden Transversalwelle bei vorhandenem oder nicht vorhandenem Wasser ausgenutzt, indem die Amplitudendifferenzen zwischen dem 1. und 3. Sprung ausgewertet werden. In Zusammenarbeit mit Siemens/KWU wurde ein EMUS-Prototypsy stem zur Fuellstandskontrolle aufgebaut und im Kernkraftwerk Grundremmingen installiert. Es sind zwei Messebenen am RDB etwa in Hoehe des Normalfuellstandes angeordnet, um bei betrieblichen Fuellstandstransienten das Verhalten der Messsignale des EMUS-Systems im Vergleich mit der bewaehrten Fuellstandsmessung nach dem Differenzdruckverfahren ueberpruefen zu koennen. Es wird ueber erste betriebliche Erfahrungen mit dem EMUS-System berichtet. Ein Vergleich der Messergebnisse des EMUS- und Differenzdruckverfahren zeigt eine gute Korrelation der Messwerte. |
| UT: | elektromagnetische Warmsonde; Fuellstandskontrolle; Longitudinalwelle; RDB; Siedewasserreaktor; SV-Welle; Ultraschall |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Inspection of dissimilar metal welds using horizontally polarized shear -SH-waves and electromagnetic ultrasonic -EMUS-probes |
| AU: | Huebschen, G.; Salzburger, H.J. |
| SO: | International journal of pressure vessels and piping 39 (1989), S.331-344 ISSN 0308-0161 |
| DT: | Journal |
| LA: | en |
| CC: | 03.25 |
| AB: | Ultrasonic testing of dissimilar metal welds is complicated by the coarse anisotropic grain structure of the weld metal and by the mismatch of the acoustic impedance at the base metallweld metal interface, which results in enhanced scattering, sound beam deviation and distortion, reflection and refraction of the incident sound field at the base metall/weld metal interface. It is known that the propagation of SV-waves is much more influenced by the structure of the weld metal than the progagation of SH-waves. This paper presents results for the surface inspection of the near probe as well as of the far probe surface of dissimilar metal welds with SH-wave EMUS-probes. Measurements were carried out from the ferritic base metal by EMUS probes with electromagnets and from the austenitic base metal by probes with permanent magnets. In particular, results of investigations concerning the testing of dissimilar metal welds in a nuclear power plant of advanced technology are reported. These diss imilar metal welds cannot be inspected with conventional ultrasonic testing methods, but with SH-waves at grazing incidence the weld can be tested from a distance of 300 mm. |
| UT: | dissimilar metal weld; EMUS-probe; longitudinal flaw; SH-wave; surface inspection; transversal flaw |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Ueberwachung des Fuellstandes in Behaeltern mit Hilfe eines elektromagnetischen Ultraschallverfahrens -EMUS-. Anwendungsbeispiel - Reaktordruckbehaelter eines Siedewasserreaktors |
| AU: | Walleser, A.; Loehr, E.; Huebschen, G. |
| SO: | Jahrestagung Kerntechnik, Bonn, INFORUM 1989, S.579-582 Conference: Kerntechnik <1989, Duesseldorf> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Es wurde ein elektromagnetisches Ultraschallmesssystem zur Ueberwachung der Fuellhoehe von Fluessigkeiten in Behaeltern aus elektrisch leitfaehigem Material entwickelt. Dieses binaer arbeitende Messsystem, mit dem diskrete Fuellstandsmarken ueberprueft werden koennen, zeichnet sich durch folgende Eigenschaften aus: - einsetzbar bis zu Temperaturen von 300 Grad C (derzeitiger Stand der Entwicklung) - einfache Befestigung an der Behaelteraussenwand - eindeutige Signalbildung bei den Mediumszustaenden: - Fluessigkeit - Gas - Fluessigkeit-Gas-Gemisch. Nach erfolgreich abgeschlossenen Laborversuchen wurde ein EMUS-System zur Fuellstandsueberwachung am Reaktordruckbehaelter im Kernkraftwerk Gundremmingen Block B fuer einen Langzeittest unter Anlagenbedingungen installiert. |
| UT: | EMUS-Pruefkopf; Fuellstandsueberwachung; RDB; Siedewasserreaktor; Ultraschall |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Ultraschallpruefung bei erhoehten Temperaturen mit elektromagnetischen Ultraschall-EMUS-Wandlern |
| AU: | Huebschen, G.; Salzburger, H.J. |
| SO: | Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung e.V. -DGZfP-, Berlin Moderne ZfP - Analysen und Prognosen Berlin/West: 1989, S.468-457 Conference: Deutsche Gesellschaft fuer Zerstoerungsfreie Pruefung (Jahrestagung) <1989, Kiel> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Das zerstoerungsfreie Pruefen und Messen an Komponenten bei erhoehten Temperaturen gewinnt sowohl bei der Fertigung als auch im Betrieb zunehmend an Bedeutung. Dabei stehen nicht nur der Sicherheitsgewinn im Vordergrund, sondern auch finanzielle Apsekte, wenn z.B. Reaktoren fuer ihre Ueberwachung nicht abgeschaltet werden muessen. Die wichtigsten Bedarfsfelder hierfuer liegen in der - Kerntechnischen Industrie WKP am SNR (250 Grad) und HTR (bis zu 250 Grad) Stationaere Ueberwachung belassener Anzeigen bzw. Fehler oder/und Bereiche mit relativ hohem Beanspruchungsniveau Stationaere Kontrolle des Fuellstandes von Behaeltern - Stahlindustrie Fertigungspruefung vo Strangguss-Vormaterial (Brammen, Knueppel) und beim Fertigwalzen in einer Hitze (Bandgiessen), Dickenmessungen (insbesondere von Rohrwaenden) - Chemischen Industrie Wanddickenmessung zum Nachweis von Korrosionsschaeden - Verarbeitenden Industrie Pruefung in der Schweisswaerme. Es wird die Weiterentwicklung der EMUS-Technologie fuer den Dauereinsatz be i Temperaturen zu 300 Grad C (ohne Kuehlung) dargestellt. Des weiteren wird ueber diesen Entwicklungen zugrundeliegende Anwendungen der Ultraschall-Warm-Pruefung im kerntechnischen Bereich berichtet. |
| UT: | EMUS-Warmpruefkopf; Fertigungspruefung; Mischnahtpruefung; RDB; SNR-300; stationaere Fuellstandsueberwachung; Strangguss |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Quantitative modeling and experimental analysis of the physical properties of electromagnetic-ultrasonic transducers. |
| AT: | Quantitative Modellierung und experimentelle Analyse der physikalischen Eigenschaften elektromagnetischer Ultraschallwandler |
| AU: | Wilbrand, A. |
| SO: | Review of Progress in Quantitative Nondestructive Evaluation. 7A New York: Plenum Publishing, 1988, S.671-680 (Review of Progress in Quantitative Nondestructive Evaluation, 7A) Conference: Annual Review of Progress in Quantitative Nondestructive Evaluation <14, 1987, Williamsburg/Va.> |
| DT: | Conference |
| LA: | en |
| CC: | 03.25 |
| AB: | The performance of electromagnetic-ultrasonic (EMUS) transducers on electrically conducting, ferromagnetic elastic material is theoretically described for transmission and reception of bulk waves and Rayleigh waves. The transduction process is modeled through the superposition of a Lorentz force mechanism, a magnetization mechanism and a magnetostriction mechanism. Directivity patterns and sensitivities are calculated for transducers with a given rf coil geometry and magnetic bias field orientation. From the sensitivities of the transmitting and the receiving transducer the transfer impedance of the whole system is obtained. Transfer impedances of various transducer configurations for the excitation of shear waves in iron have been measured as a function of frequency, angle of incidence, and bias field strength and have been compared to the theoretical results. From the out-come of this study, it is concluded that the transducer model gives a valid description of the physical laws unde rlying the transducer behaviour and can be used for quantitative estimations in EMUS probe design. (IZFP) |
| UT: | Absolutmessung; Eisen; Empfindlichkeit; Frequenzabhaengigkeit; Leitfaehigkeit(elektrisch); Linienwandler; Magnetostriktion; Metall; Modell(mathematisch); Permeabilitaet; Richtcharakteristik; Transversalwelle; Ultraschall; Ultraschallwandlung(beruehrungslos); Ultraschallwandlung(elektromagnetisch); Untersuchung(experimentell); Werkstoff(magnetisch); Winkelpruefkopf |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Zerstoerungsfreie Pruefungen im Rahmen des PISC II-Programms |
| AU: | Schmuelling, W.; Deuster, G.; Weiss, R. |
| SO: | 12. MPA-Seminar '86 1986, S.12.1-12.20 Conference: MPA-Seminar <12, 1986, Stuttgart> |
| DT: | Conference |
| LA: | de |
| CC: | 03.25 |
| AB: | Es werden die im Rahmen des PISK II-Programmes durchgefuehrten Pruefungen beschrieben. Die Ergebnisse der benutzten Handpruefverfahren nach der KTA-Regel 3201.3 werden diskutiert und mit anderen Regelwerken verglichen. Das Auffindvermoegen fuer die verschiedenen Fehlerarten wird aufgezeigt. Fuer ausgewaehlte Fehlerbereiche an den verschiedenen Testkoerpern wurden zur Fehleranalyse moderne Verfahren wie ALOK, HOLOSAFT und Phased Array eingesetzt. Die erzielten Ergebnisse werden mit den Ergebnissen der Radiographie und der zerstoerenden Pruefung verglichen. Das Vermoegen der SH-Wellen zur Detektion von Inneroberflaechenfehlern bei der Aussenpruefung wird aufgezeigt. Ferner werden die Ergebnisse der PISK II-Parameterstudie dargestellt. An einem plattierten Testkoerper, mit oberflaechennahen Fehlern, wurden die Verfahren EMUS und Wirbelstrom eingesetzt. (IZFP) |
| UT: | ALOK; EMUS; HOLOSAFT; MFWS; phased array; PISK II |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Electromagnetic ultrasonic testing |
| AU: | Hoeller, P.; Wilbrand, A. |
| SO: | Traitement du Signal 2 (1985), Nr.5, S.459-464 |
| DT: | Journal |
| LA: | en |
| CC: | 03.25 |
| AB: | An overview is given of the EMUS transduction technique, its physical foundations, transducer construction, laboratory developments and applications. The flexibility in transducer construction permits the excitation of a large variety of bulk waves and guided wave modes. Important application fields for the EMUS transducers are nondestructive testing with Rayleigh waves, SH waves and shear waves with normal incidence since, for these wave types, conventional excitation through a couplant suffers serious drawbacks. |
| UT: | EMAT; EMUS; magneto-acoustic conversion; surface wave |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Moderne Verfahren der Ultraschallpruefung |
| AU: | Barbian, O.A.; Gebhardt, W.; Salzburger, H.J.; Schmitz, V. |
| SO: | Materialpruefung 27 (1985), Nr.3, S.49-56 ISSN 0025-5300 |
| DT: | Journal |
| LA: | de |
| CC: | 03.25 |
| AB: | Es wird ueber den Stand der im IzfP gelaufenen Entwicklungen und Forschungen zu Ultraschallpruefverfahren mit quantitativer Interpretation, insbesondere Fehlerrekonstruktion, berichtet. Grundprinzip, physikalische Grenzen, Geraetetechnik und Anwendungsfaelle fuer den Einsatz von ALOK, PHASED ARRAY, HOLOSAFT und EMUS werden praxisnah erlaeutert. |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Ultraschallpruefung mit elektromagnetischen Wandlern |
| AU: | Huebschen, G.; Repplinger, W.; Salzburger, H.J. |
| SO: | FhG-Berichte (1984), Nr.1, S.23-32 : Abb.,Lit. ISSN 0342-1953 |
| DT: | Journal |
| LA: | de |
| CC: | 03.25 |
| UT: | Elektromagnetismus; EMUS-Wandler; Ultraschallpruefung; Wandler |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | EMUS-probes for bulk waves and Rayleigh waves. Model for sound field and efficiency calculations |
| AU: | Wilbrand, A. |
| SO: | New procedures in nondestructive testing Berlin/West: Springer, 1983, S.71-80 |
| DT: | Article |
| LA: | en |
| CC: | 03.25 |
| AV: | IZFP |
| ED: | 97/09/26 |
| TI: | Vergleichende Eigen-Spannungsmessungen mit zwei Geraeteprototypen und einem kommerziell verfuegbaren Geraet zur Nutzung ferromagnetischer und magnetoelastischer Messgroessen |
| AU: | Theiner, W.A.; Altpeter, I.; Repplinger, W. |
| SO: | Verein Deutscher Ingenieure -VDI-, Duesseldorf GESA-Symposium 1982 Duesseldorf: VDI-Verlag, 1982, S.85-90 (VDI-Berichte, 439) |
| DT: | Article |
| LA: | de |
| CC: | 03.25 |
| UT: | Barkhausen-Rauschen; Eigenspannung(magnetisch); EMUS; Geraeteprototyp; Magnetostriktion(dynamisch) |
| AV: | IZFP |
| ED: | 97/09/26 |