Forum Technical Discussions Re: radiography Posted by: DJ Kallhof (PID_1317), E-mail: Address, on May 15, 2008 at 14:14 : In Reply to: Re: radiography posted by : Nigel , E-mail: Address, on May 15, 2008 at 08:26 : I performed industrial radiography for 8 years before settling into aerospace. I may be able to offer some insight. The source size of your typical Ir 192 source is app. 0.100" X 0.100" (.00393mm X .00393mm) yielding an effective source size of 0.141" (.0055mm). If memory serves me, the portal on most collimators was app. somewhere between .250" -.375" (.0098mm - .01476mm). The beam spread in industrial radiography is dictated by the effective source size of the isotope, the portal of the collimator simply allows that to occur. The source simply floats somewhere in the opening of the much larger collimator portal. The function of the collimator is for the safety of the radiographer and anyone outside the ropes. ----------- Start Original Message ----------- : "No any change in beam spread"? What would be the purpose of collimators if they dont restrict the beam spread, Gowri? Perhaps you misunderstood Nandeesh's question. : Nandeesh, the collimator supplier should have provided a data sheet at the time of purchase detailing material, dimensions and beam spread. If you dont have that then theoretically you could make a set-up using a 40 x 30 film and precisely measure the source to film distance, expose for a couple of seconds to the collimated beam and measure the dimensions of the significant exposure on the developed film. At least it would give you a qualitative idea of the beam cone. : Hope that helps. Safe (as possible) shooting! : Nigel : : : Can u pls tell me how to estimate the beam spread in Gamma radiography when using A COLLIMATOR? : : Hi, : : This is Gowri from GJ. First of all we have to know that collimator is used to guide the radiation and for safe practice in dangerous Radiography. collimators are made up of high density metals eg. tungsten and heavy alloys to absorb the non required ionising radiation for safety. I think so there is no any change in beam spread when using collimators, rather than as usual. ------------ End Original Message ------------ Follow Ups: Re: radiography Nigel 17:19 May-16-2008 (3) Re: radiography Nigel 17:23 May-16-2008 (2) Re: radiography DJ Kallhof 21:14 May-16-2008 (1) Re: radiography tj 14:17 May-29-2008 (0) Post a Followup: Name: E-Mail: Subject: Comments: ----------- Start Original Message ----------- : I performed industrial radiography for 8 years before settling into aerospace. I may be able to offer some insight. The source size of your typical Ir 192 source is app. 0.100" X 0.100" (.00393mm X .00393mm) yielding an effective source size of 0.141" (.0055mm). If memory serves me, the portal on most collimators was app. somewhere between .250" -.375" (.0098mm - .01476mm). The beam spread in industrial radiography is dictated by the effective source size of the isotope, the portal of the collimator simply allows that to occur. The source simply floats somewhere in the opening of the much larger collimator portal. The function of the collimator is for the safety of the radiographer and anyone outside the ropes. : : "No any change in beam spread"? What would be the purpose of collimators if they dont restrict the beam spread, Gowri? Perhaps you misunderstood Nandeesh's question. : : Nandeesh, the collimator supplier should have provided a data sheet at the time of purchase detailing material, dimensions and beam spread. If you dont have that then theoretically you could make a set-up using a 40 x 30 film and precisely measure the source to film distance, expose for a couple of seconds to the collimated beam and measure the dimensions of the significant exposure on the developed film. At least it would give you a qualitative idea of the beam cone. : : Hope that helps. Safe (as possible) shooting! : : Nigel : : : : Can u pls tell me how to estimate the beam spread in Gamma radiography when using A COLLIMATOR? : : : Hi, : : : This is Gowri from GJ. First of all we have to know that collimator is used to guide the radiation and for safe practice in dangerous Radiography. collimators are made up of high density metals eg. tungsten and heavy alloys to absorb the non required ionising radiation for safety. I think so there is no any change in beam spread when using collimators, rather than as usual. ------------ End Original Message ------------ Optional Link URL: Example: "http://www....html". Alternative write "http://www.ndt.net/wshop/attach/filename.htm" if you transfered a filename.htm via FTP Page Title: is important! Optional Image URL: http://www....gif Attention! Please click the button only once. This may take a moment to process Forum Technical Discussions Help