where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1284 views
Technical Discussions
Pablo Katchadjian
Engineering, -
Comision Nacional de Energia Atomica, Argentina, Joined Oct 1999, 1

Pablo Katchadjian

Engineering, -
Comision Nacional de Energia Atomica,
Argentina,
Joined Oct 1999
1
08:05 Aug-13-1999
UT in explosive zone

Please,I want to know if there are some security
restrictions(risk)in use an UT equipment,powered
with batteries,on a top of a petroleum tank
(Explosive Zone).
Many thanks.
Pablo.




 
 Reply 
 
Norm Woodward
Norm Woodward
08:29 Aug-13-1999
Re: UT in explosive zone
: Please,I want to know if there are some security
: restrictions(risk)in use an UT equipment,powered
: with batteries,on a top of a petroleum tank
: (Explosive Zone).
: Many thanks.
: Pablo.

Number one rule is: Never change transducers, or cables, while the machine is running. This applies even if the system is certified for use in explosive environments by the UL or anyone else.

I would also think that there would be some requirement for a ground strap to be between the UT unit and your tank, but I am not sure.

I don't know of any certified "explosion-proof" UT units, but I am sure we will hear from those who do.

Good Luck,

Norm



 
 Reply 
 
Robert (Rocky) A. Day
Engineering
Milky Way Jewels, USA, Joined Nov 1998, 40

Robert (Rocky) A. Day

Engineering
Milky Way Jewels,
USA,
Joined Nov 1998
40
00:02 Aug-14-1999
Re: UT in explosive zone
Comments on not hot swaping the transducers are appropriate. You should not swap any line in an explosives area and other actions may be needed. Sparks caused by static electricity, clothing and shoes etc are a danger, are an example. Sparks can also be generated by metal-to-metal impact and metal-to-stone impact. Flamable vapors can be a significant hazard and should be treated with respect.

A good place to start is the National Fire Protection Association which has many Codes and Standards associated with explosion safety. I do not recall the NFPA Code, but some reading may help locate resources of value.

The second resource is the National Electrical Manufacturers Association which provides standards for exposion proofing electrical equipment. This standard will provide information of use both in buying equipment and in retrofitting existing equipment.

Regards,
Robert (Rocky) A. Day
Second Sound
Ultrasonic Systems
904 Cortland Avenue
San Francisco, CA 94110
(415) 641-4947
Fax: (415) 641-5502

: Please,I want to know if there are some security
: restrictions(risk)in use an UT equipment,powered
: with batteries,on a top of a petroleum tank
: (Explosive Zone).
: Many thanks.
: Pablo.

:




 
 Reply 
 
Dave Cartwright
Dave Cartwright
00:17 Aug-16-1999
Re: UT in explosive zone
: Please,I want to know if there are some security
: restrictions(risk)in use an UT equipment,powered
: with batteries,on a top of a petroleum tank
: (Explosive Zone).
: Many thanks.
: Pablo.

: Pablo, The earlier advice should be viewed with caution, there is much speculation about electrical equipment for use in hazardous atmospheres. You should review official standards and/or documentation. There are EN standards that cover this subject. See EN-60079 for details of equipment and hazardous area classification and EN 50020 and EN-50014 for equipment testing and certification. Note that ONLY certified equipment should be used.

Please contact me direct if you need further advise.

Dave Cartwright




 
 Reply 
 

Product Spotlight

32:128PR PAUT & 2-ch TOFD Flaw Detector: SyncScan 2

●32:128PR PAUT with optional 2-ch TOFD to maximize your efficiency ●Support PR mode for corrosi
...
on inspection ●Multiple solutions for welds & corrosion ●Faster scan speed (Approximately 3 meters/minute) ●Light weight: 4kg only including battery
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window