where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1339 views
Technical Discussions
B. Johnson
B. Johnson
07:14 Apr-05-2007
Steel - Rubber debond testing method?

I am looking for a methodology that is capable of detecting bonding/adhesive failures between a rubber type compound and heavy steel plating, and determine if off-the-shelf testing equipment is available.
The steel-side surface is mostly inaccessible. Testing must either be done from the rubber surface, or from very limited locations on the steel-side surface.
The rubber compound is approximately 2" thick and cannot be penetrated by ultrasound, at any frequency.
Critical size of debond has not been determined.

Thank you,
B Johnson
NDT Engineering
General Dynamics, Electric Boat


    
 
 Reply 
 
joerg collrep
Director, - Sales NDT
Dantec Dynamics GmbH, Germany, Joined Jan 2006, 4

joerg collrep

Director, - Sales NDT
Dantec Dynamics GmbH,
Germany,
Joined Jan 2006
4
08:32 Apr-05-2007
Re: Steel - Rubber debond testing method?
you should try shearography which has proved to detect easily voids inside rubber. we load your part with vacuum and the defect expands to the surface. if you need more info pls let me know or visit our homepage. best regards joerg----------- Start Original Message -----------
: I am looking for a methodology that is capable of detecting bonding/adhesive failures between a rubber type compound and heavy steel plating, and determine if off-the-shelf testing equipment is available.
: The steel-side surface is mostly inaccessible. Testing must either be done from the rubber surface, or from very limited locations on the steel-side surface.
: The rubber compound is approximately 2" thick and cannot be penetrated by ultrasound, at any frequency.
: Critical size of debond has not been determined.
: Thank you,
: B Johnson
: NDT Engineering
: General Dynamics, Electric Boat
------------ End Original Message ------------




    
 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
01:14 Apr-05-2007
Re: Steel - Rubber debond testing method?
In other situations where the rubber is thinner and more transmissive to ultrasound, we usually recommend a phase shift test using any common flaw detector and an appropriate transducer, but you indicate that won't work here due to extreme attenuation. Alternately, if testing from the points where you do have access to the steel is useful, it should be possible to evaluate the steel/rubber bond from the steel side using the ringdown technique described in the attached application note.

----------- Start Original Message -----------
: I am looking for a methodology that is capable of detecting bonding/adhesive failures between a rubber type compound and heavy steel plating, and determine if off-the-shelf testing equipment is available.
: The steel-side surface is mostly inaccessible. Testing must either be done from the rubber surface, or from very limited locations on the steel-side surface.
: The rubber compound is approximately 2" thick and cannot be penetrated by ultrasound, at any frequency.
: Critical size of debond has not been determined.
: Thank you,
: B Johnson
: NDT Engineering
: General Dynamics, Electric Boat
------------ End Original Message ------------




    
 
 Reply 
 
Thomas F. Murphy
Thomas F. Murphy
07:15 Apr-06-2007
Re: Steel - Rubber debond testing method?
Hello all,

My employer, GE Inspection has a system used for this application in rubber covered rolls. It operates by the principle of heating the metal from the rubber, inductively, and monitoring the transferred heat to the rubber. Lack of thermal transfer indicates a lack of bond. If you are interested in it I will give you the correct contacts for further information.

Kind regards all,
Tom

Kindest regards,
Tom




    
 
 Reply 
 
Trevor Easton
Engineering
Dofasco Inc, Canada, Joined Nov 1998, 13

Trevor Easton

Engineering
Dofasco Inc,
Canada,
Joined Nov 1998
13
04:53 Apr-13-2007
Re: Steel - Rubber debond testing method?
You might try a sub sonic method. Determine the natural frequency of a bonded portion of the rubber using a shaker. Then measure the natural frequency of a debonded portion. If there is a significant difference then a scan of the surface to measure the frequency response will provide an indication of debonding. You will of course have to develop your own transducer but it shouldn't be to difficult to adapt a small electric motor with offset mass and an accelerometer into a simple hand held monitor. Maybe a roller ball to ease the job of scanning across large areas. Perhaps an electro magnet driven at the appropriate frequency(s) the variation in its behaviour over bonded and unbonded rubber indicating areas of concern.

----------- Start Original Message -----------
: I am looking for a methodology that is capable of detecting bonding/adhesive failures between a rubber type compound and heavy steel plating, and determine if off-the-shelf testing equipment is available.
: The steel-side surface is mostly inaccessible. Testing must either be done from the rubber surface, or from very limited locations on the steel-side surface.
: The rubber compound is approximately 2" thick and cannot be penetrated by ultrasound, at any frequency.
: Critical size of debond has not been determined.
: Thank you,
: B Johnson
: NDT Engineering
: General Dynamics, Electric Boat
------------ End Original Message ------------




    
 
 Reply 
 

Product Spotlight

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

FlexoFORM™

The FlexoFORM™ solution integrates flexible phased array probe technology in a scanner to solv
...
e the challenges that come with inspecting pipe elbows. When combined with a water column, this solution can be used to collect easy-to-interpret data on elbows with diameters ranging from 4.5 in. OD up to flat and offers many benefits.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window