where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
879 views
Technical Discussions
steve
NDT Inspector,
Bureau Veritas Asset Integrity & Reliability Services, Australia, Joined Aug 2005, 6

steve

NDT Inspector,
Bureau Veritas Asset Integrity & Reliability Services,
Australia,
Joined Aug 2005
6
00:55 Dec-27-2007
NDT Capability

Wow...It is a scary world!

It is my perception that there is a rising frequency of posts to this forum from inexperienced technicians, particular in the fields of ultrasonics and radiography, asking questions that should be addressed by training, in-house procedures and Level III supervisors.

This Technical Discussions Forum is a great tool for seeking peer review, or advice, from NDT practitioners that are faced with a task that is outside of their normal scope of testing.

It is also a great forum to discuss the merits or failings of codes, standards or inspection technologies.

It should not be seen as a replacement or stop-gap for training.

Please don't misunderstand me, I am not critical of the persons posting the messages, in fact I applaud them for seeking the advice of their worthy peers that take the time to attempt to assist them where they can.

However, I do wonder why they use this forum for this purpose. Is it because they don't have, or have access to, training, in-house procedures and Level III supervisors?

If this is the case, our industry is in trouble.


 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
03:30 Dec-31-2007
Re: NDT Capability
Steve,

You are right. While we should certainly applaud and appreciate their inerest in learning, the situation does point to an alarming situation where they are required to fend for thenselves without any help inhouse. Cost cutting measures, appear smart in the short run but can be catastrophic.

Let us help them as much as we can, keeping the safety aspects in view.

Swamy


----------- Start Original Message -----------
: Wow...It is a scary world!
: It is my perception that there is a rising frequency of posts to this forum from inexperienced technicians, particular in the fields of ultrasonics and radiography, asking questions that should be addressed by training, in-house procedures and Level III supervisors.
: This Technical Discussions Forum is a great tool for seeking peer review, or advice, from NDT practitioners that are faced with a task that is outside of their normal scope of testing.
: It is also a great forum to discuss the merits or failings of codes, standards or inspection technologies.
: It should not be seen as a replacement or stop-gap for training.
: Please don't misunderstand me, I am not critical of the persons posting the messages, in fact I applaud them for seeking the advice of their worthy peers that take the time to attempt to assist them where they can.
: However, I do wonder why they use this forum for this purpose. Is it because they don't have, or have access to, training, in-house procedures and Level III supervisors?
: If this is the case, our industry is in trouble.
------------ End Original Message ------------




 
 Reply 
 
Michel
NDT Inspector,
consultant, Canada, Joined Sep 2006, 868

Michel

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
868
07:31 Jan-03-2008
Re: NDT Capability
Hi Guys,

I've been in the NDT business since 1989 and got my training from the Canadian Air Force. I retired in 1996 and was able to gain experience in various industries, yet I don't know it all.

With our profession changing so fast, no amount of training and supervision will teach you everything. This forum is in my opinion a place where we as technician can come and learn about a situation we might have not encounter before. In the past, I've worked with helpers that were very knowledgeable in their industry and also with Level 3 that were unfamiliar with my industry.

I guess what I'm trying to say is that we should keep an open mind. Helping and teaching one another will only reflect positively on our profession.

----------- Start Original Message -----------
: Steve,
: You are right. While we should certainly applaud and appreciate their inerest in learning, the situation does point to an alarming situation where they are required to fend for thenselves without any help inhouse. Cost cutting measures, appear smart in the short run but can be catastrophic.
: Let us help them as much as we can, keeping the safety aspects in view.
: Swamy
:
: : Wow...It is a scary world!
: : It is my perception that there is a rising frequency of posts to this forum from inexperienced technicians, particular in the fields of ultrasonics and radiography, asking questions that should be addressed by training, in-house procedures and Level III supervisors.
: : This Technical Discussions Forum is a great tool for seeking peer review, or advice, from NDT practitioners that are faced with a task that is outside of their normal scope of testing.
: : It is also a great forum to discuss the merits or failings of codes, standards or inspection technologies.
: : It should not be seen as a replacement or stop-gap for training.
: : Please don't misunderstand me, I am not critical of the persons posting the messages, in fact I applaud them for seeking the advice of their worthy peers that takethe time to attempt to assist them where they can.
: : However, I do wonder why they use this forum for this purpose. Is it because they don't have, or have access to, training, in-house procedures and Level III supervisors?
: : If this is the case, our industry is in trouble.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Magnetic X-Ray Pipeline Crawler

Zhong Yi brand pipeline crawler is magnetic/micro-video controlled crawler with DC X ray unit inst
...
alled for checking welding of pipeline. Move steadily inside the pipeline 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometers and provide the efficient inspection of the pipeline.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window