where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

YXLON Copenhagen
YXLON Copenhagen is a highly specialized, award winning Danish company with 60 years of experience in portable X-ray solutions for industrial NDT.
906 views
Technical Discussions
faran
Engineering
FFC Pakistan, Pakistan, Joined May 2005, 17

faran

Engineering
FFC Pakistan,
Pakistan,
Joined May 2005
17
10:39 Mar-19-2009
SCC crack detection in SS

We have witnessed SCC in one of our columns, the cause of SCC is the Chroride presence in wet insulation. Now what NDT is usefull to detect the extent of attack quickly & effectively. PT we have done, MT is not applicable, How about Phased Array Eddy Current, is it sensitive enough to detect micro cracks, what about Omniscan. Do you think Metallography would help.

    
 
 Reply 
 
J. Mark Davis
Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama, USA, Joined Mar 2000, 85

J. Mark Davis

Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama,
USA,
Joined Mar 2000
85
12:22 Mar-19-2009
Re: SCC crack detection in SS
In Reply to faran at 10:39 Mar-19-2009 (Opening).

Detection of SCC for your application can be accomplished with OD Creeping Waves very effectively. OD Creeping Waves have been demonstrated to detect cracks on the scanning surface with a depth of 0.005 inches and less.

Phased Arrays are equally effective for detection and sizing of SCC. Even Phased Array using Creeping Waves would be effective.

Some questions are: what is the material type and what is the thickness.

Is detection your only concern. Do you need to size these Stress Corrosion Cracks.

What is your Critical Flaw Size?

To conclude this is a very easy application using Conventional OD Creeping Waves or using an OmniScan Phased Array System. The images you will get with the OmniScan will significantly help with detection and characterization.

Sincerely,

J. Mark Davis

    
 
 Reply 
 
Luis Ganhao
Engineering,
USA, Joined Sep 2008, 25

Luis Ganhao

Engineering,
USA,
Joined Sep 2008
25
15:02 Mar-19-2009
Re: SCC crack detection in SS
In Reply to faran at 10:39 Mar-19-2009 (Opening).

You can use TOFD to detect, size and carcaterized the SCC probably your unique limitation could be the thickness, however I could detect this kind of cracks in low thickness (9mm Lab testings). The setttieng-up (probes, frequency,size) is the clue for this application

    
 
 Reply 
 

Product Spotlight

NEW! The PragmaPro Instrument Platform

The PragmaPro is based on a modular cartridge technology and supports various NDT instrument modal
...
ities such as UT, PAUT, ECT and many more. This new platform is based on a machined, powder-coated aluminum frame for shock-proofness, best sealing qualities and maximum heat dissipation. This is practical to extend the outdoor temperature range and/or to extend the power injected in the transducers. The PragmaPro is aiming at a very wide range of applications, such as weld scanning, corrosion mapping and composite testing.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Magnetic X-Ray Pipeline Crawler

Zhong Yi brand pipeline crawler is magnetic/micro-video controlled crawler with DC X ray unit inst
...
alled for checking welding of pipeline. Move steadily inside the pipeline 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometers and provide the efficient inspection of the pipeline.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window