where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
736 views
Technical Discussions
Asim Niazi
NDT Inspector
Inspection Unit, Fauji Fertilizer Co., Pakistan, Joined Jul 2001, 6

Asim Niazi

NDT Inspector
Inspection Unit, Fauji Fertilizer Co.,
Pakistan,
Joined Jul 2001
6
07:47 Jul-02-2001
High Temperature UT

Q. Is it possible to flaw size a crack inside turbine casing TAPER portion ? Material Chrom-Moly steel at 150 degrees celsius. UT was performed with high temperature miniature probe 45, 60 degrees. Main crack depth was detected but crack ends could not be monitored as travelling in the raduius of taper portions of flange.


 
 Reply 
 
Asim Niazi
NDT Inspector
Inspection Unit, Fauji Fertilizer Co., Pakistan, Joined Jul 2001, 6

Asim Niazi

NDT Inspector
Inspection Unit, Fauji Fertilizer Co.,
Pakistan,
Joined Jul 2001
6
08:51 Jul-04-2001
Re: High Temperature UT on KS Turbine Casing crack.
We have experienced cracks in our Synthesis machine steam inlet nozzles which are low alloy casting. We are monitoring the depth of the cracks by using Krautkramer Gmbh probes (W45B2GV & W60B2GV) only in the straight portion due to the constructional constraints of the probes. These probes were procured to acquire data on intricate and small radius surfaces at elevated temperature service. But installation of large dimension wedges (to avoid the exposure of probe crystal to high temperature) is restricting the utilization practically for straight surfaces only. Subsequently ends monitoring cannot be ensured due to the crack propagation in nozzle curvature at one side and variable thickness portion on other side.

Can anyone please advice us regarding any other high temperature miniature angle probe or alternate non-destructive technique, which can be used to monitor the cracks depth as well as the length.

ASIM NIAZI



 
 Reply 
 
Mahar Mrumat Khan
Mahar Mrumat Khan
05:16 Aug-25-2001
Re: crack hmmmmmmmmmm
Get a new one dumbo


 
 Reply 
 
Fred Raco, Jr.
Director
CP Industries - Div. of Reunion Industries, Inc., USA, Joined Jan 2001, 6

Fred Raco, Jr.

Director
CP Industries - Div. of Reunion Industries, Inc.,
USA,
Joined Jan 2001
6
03:42 Aug-27-2001
Re: crack hmmmmmmmmmm
: Get a new one dumbo
.This member should be banned from leaving any more messages.



 
 Reply 
 

Product Spotlight

Surf-X® Array Probe

Introducing the Surf-X family of flexible Eddy Current Array (ECA) probes. Featuring unique multiple
...
coil sets and proprietary X-PROBE technology, Surf-X array probes can quickly and accurately handle a range of inspection applications, from inspecting corrosion or cracking in pipes, pressure vessels, or tanks, to assessing and sizing cracks in raised welds and friction stir welds.
>

NDTkit RT

NDTkit RT, TESTIA's Digital Radiography software The NDTkit product line software for X-ray analysi
...
s. NDTkit RT is a software benefiting from the Ultis kernel which is dedicated to radiographic image analysis. It offers a set of tools and filtering processes to assist RT operators in finding relevant flaws.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window