where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Eddyfi
Eddyfi Technologies provide the most advanced NDT technologies in the world, helping OEMs, asset owners and service companies enhance productivit ...
1317 views
Technical Discussions
Gabriel
Consultant,
Canada, Joined Oct 2009, 2

Gabriel

Consultant,
Canada,
Joined Oct 2009
2
18:32 Oct-08-2009
Concrete NDT and destructive testing

What would be the most common testing (both NDT and destructive testing)methods for pre-cast concrete products. Some methods I can see are the slump test, compression test and hardness tests. What other testing methods are common for this application? Thanks in advance

 
 Reply 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
20:09 Oct-08-2009
Re: Concrete NDT and destructive testing
In Reply to Gabriel at 18:32 Oct-08-2009 (Opening).

Gabriel,

I know of the PUNDIT machine for testing concrete. I googled PUNDIT and this led to the present equipment manufacturer, Proceq - they also make the Equotip hardness tester. So go to www.proceq.com for a wide variety of concrete testing electronic equipment.

Cheers

Nigel

 
 Reply 
 
Gabriel
Consultant,
Canada, Joined Oct 2009, 2

Gabriel

Consultant,
Canada,
Joined Oct 2009
2
02:03 Oct-09-2009
Re: Concrete NDT and destructive testing
In Reply to Nigel Armstrong at 20:09 Oct-08-2009 .

Thank you for the information. I had a look at them and it is very useful. Can you think of any other NDT for quality control?

 
 Reply 
 
Ernst Niederleithinger
R & D, -
BAM (Fed. inst. for material research and testing, Germany, Joined Jun 2001, 7

Ernst Niederleithinger

R & D, -
BAM (Fed. inst. for material research and testing,
Germany,
Joined Jun 2001
7
08:18 Oct-09-2009
Re: Concrete NDT and destructive testing
In Reply to Gabriel at 02:03 Oct-09-2009 .

Gabriel,

there are a lot of additional methods (and manufacturers) around. There are eddy current and radar devices e. g. for checking rebar location or acoustic methods (impact echo, ultrasonics) for checking geometry , quality, inhomogeneities.... You can even X-ray.
What is best for you, depends on your application. If you decribe the "precast concrete products" and the problems you expect a little more in detail, I (and others) could recommend suitable methods.

Regards, Ernst

 
 Reply 
 
Martin Schickert
R & D,
Institute for Materials Research and Testing, Germany, Joined Jan 2000, 18

Martin Schickert

R & D,
Institute for Materials Research and Testing,
Germany,
Joined Jan 2000
18
09:28 Oct-09-2009
Re: Concrete NDT and destructive testing
In Reply to Gabriel at 18:32 Oct-08-2009 (Opening).

Gabriel,

the usage of destructive testing methods on pre-cast concrete products depends
1. on the standards applicable to the product in the respective country and
2. on the techniques the manufacturer has found useful for quality control. There is a wide range of possibilies.

Concerning non-destructive methods, I am not aware of any standards. Ultrasonic through transmission has been used for quality control for a long time. Changes of the pulse velocity indicate variations in the manufacturing process, cracks, or other problems.

During the last few years non-destructive testing methods have been developed further. As an example, our institute conducts R&D on ultrasonic methods. It is now possible to measure pulse velocity without surface contact employing air-coupled transducers, or to image concrete elements from one side using electronic and mechanical scanning and 2D or 3D SAFT reconstruction.

Martin Schickert

 
 Reply 
 
Simon Amallraja
Simon Amallraja
14:41 Oct-12-2009
Re: Concrete NDT and destructive testing
In Reply to Gabriel at 18:32 Oct-08-2009 (Opening).

Check the following website: www.ultrangroup.com. They have devloped Non Contact Ultrasonic Systems for Concrete structures like Bridges, Buildings etc.,

Simon

 
 Reply 
 

Product Spotlight

Echomac® Small

Available with up to eight channels of electronics to detect and evaluate thickness, flaws and eccen
...
tricity, this UT tester is housed in a convenient, smaller cabinet. This instrument can be used in conjunction with bubbler or immersion tank systems, or with a test bench or in laboratory applications. The Echomac® Small is available in the FD4, FD6 or FD6A versions.
>

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window