where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1659 views
Technical Discussions
S.Mohamed Riaz
S.Mohamed Riaz
08:56 Jan-25-2010
High temperature Lines - Radiography

Dear experts,

We have stream lines around 450'C - 600'C, we like to take radiography for measure actual thickness.Schedule thickness is 44mm and pipeline diameter is 30".

please help us to give your most valuable ideas, whether we can take radiography with special arrangements.

regards,
riaz

 
 Reply 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
13:29 Jan-25-2010
Re: High temperature Lines - Radiography
In Reply to S.Mohamed Riaz at 08:56 Jan-25-2010 (Opening).

Mohamed

A few ideas.

I take it you dont want to remove insulation and use a high temperature ultrasonic probe and couplant.

44mm wall thickness and 88mm penetrated thickness is on the margins for producing a measurable exposure by Iridium-192 profile radiography using a ball-bearing or the Rikki-T comparator.

To measure corrosion rate without shutting lines down there are means of hot tap and installation of measuring probes.

 
 Reply 
 
Roger Duwe
NDT Inspector, API-510, 570, 653
MISTRAS, USA, Joined Jan 2009, 148

Roger Duwe

NDT Inspector, API-510, 570, 653
MISTRAS,
USA,
Joined Jan 2009
148
22:51 Jan-25-2010
Re: High temperature Lines - Radiography
In Reply to Nigel Armstrong at 13:29 Jan-25-2010 .

In addition to the wall thickness to be penetrated, the curvature will give problems. Typically, profile RT is not used above about 12-inches OD due to the curvature. 30-inch pipe will not give results accurate to use for pressure calculations or measuring material loss.

High-temp couplant and UT-thickness are probably the best method. You only need a 50-75mm hole in the insulation, and it can be replaced with a plug of fiberous insulation -- Kaowool, Cerowool, or similar.

 
 Reply 
 
ligang feng
NDT Inspector,
China, Joined Jan 2010, 3

ligang feng

NDT Inspector,
China,
Joined Jan 2010
3
02:45 Jan-26-2010
Re: High temperature Lines - Radiography
In Reply to S.Mohamed Riaz at 08:56 Jan-25-2010 (Opening).

i am strongly agree with Nigel's ideas.

 
 Reply 
 
Syed Ali
R & D,
Innerspec Technology, USA, Joined Oct 2009, 17

Syed Ali

R & D,
Innerspec Technology,
USA,
Joined Oct 2009
17
05:45 Feb-01-2010
Re: High temperature Lines - Radiography
In Reply to S.Mohamed Riaz at 08:56 Jan-25-2010 (Opening).

Try exploring EMATs for high temperature thickness measurements. Please see for High Temperature EMATs and applications.

 
 Reply 
 

Product Spotlight

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

CIVA 2017 UT Module

CIVA NDE Simulation Software is the world leader of NDT Simulation. The UT simulation Module incl
...
udes: - "Beam computation": Beam propagation simulation - "Inspection Simulation": Beam interaction with flaws or specimens The user can simulate a whole inspection process (pulse echo, tandem or TOFD) with a wide range of probes (conventional, Phased- arrays or EMAT), components, and flaws.
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window