where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
915 views
Technical Discussions
Abdulla
Engineering, CORROSION DIV. SUPERINTENDENT
SIRTE OIL COMPANY, Libya, Joined Jun 2004, 7

Abdulla

Engineering, CORROSION DIV. SUPERINTENDENT
SIRTE OIL COMPANY,
Libya,
Joined Jun 2004
7
15:01 Mar-13-2010
RT

Some times we have been asked to certify the welding activities when the welding inspector did not attend , based on using RT, is this possible, and what are the draw backs of not attending the welding operation, can we rely only on RT.
Thank you

    
 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 845

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
845
16:17 Mar-13-2010
Re: RT
In Reply to Abdulla at 15:01 Mar-13-2010 (Opening).

Abdulla,

There is a big difference in accepting a weld based on RT and having a welding inspector witnessing the welding process.

Accepting a weld based on the inerpration of a radiograph only ensure that your weld is "defect free" or has "indications acceptable to code".

The witnesing of the welding by the welding inspector serve to ensure the welding procedure was followed. Some of the items the inspector would look for would be: the weld prep, the electrode used, temperature of the base metal for preheat (if needed), certification of the welder and so on. These any many more cannot be answered by looking at a radiograph.

    
 
 Reply 
 
Phil
NDT Inspector, Radiation Safety
BINDT, MIAQP, United Kingdom, Joined Mar 2009, 151

Phil

NDT Inspector, Radiation Safety
BINDT, MIAQP,
United Kingdom,
Joined Mar 2009
151
12:25 Mar-14-2010
Re: RT
In Reply to Abdulla at 15:01 Mar-13-2010 (Opening).

Abdulla,

What Mr Couture has said is correct and you can also add if the Welding Inspector had witnessed the Welding Test you would know that the named Welder had actually Welded the test piece, and not someone else.

Regards,

    
 
 Reply 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
14:16 Mar-14-2010
Re: RT
In Reply to Abdulla at 15:01 Mar-13-2010 (Opening).

Hello Abdulla, its my belief that many welds are produced without a welding inspector present, whether RT'ed afterwards or not. High integrity welds SHOULD be witnessed and measured for ROL = run out length, heat input etc but this does not always happen. If these are not controlled within the parameters of the approved welding procedure then control of the eventual mechanical strength of the joint is lost. This is not a situation detectable by NDT, which searches for discontinuities and not properties - that is why the weld PQR shows both the actual welding parameters used and the results of the necessary mechanical DESTRUCTIVE tests. The WPS will allow a controlled range of parameters based on the record of those parameters used to complete the joint.

As for "can we rely on RT", if the weld is unwitnessed and RT is the contractual requirement, that is all you will have. The controlling Code will to some degree stipulate quality requirements for the RT but these are minimal - density within limits and penetrameter appropriate hole/wire visibility. Acknowledging RT's capabilities are linked to defect morphology then you need to consult appropriate Probability of Detection tables for RT of various defect types to know if RT is the back-stop for any potential welding ills. The end user should stipulate and monitor production and inspection processes proportionate with the product criticality.

    
 
 Reply 
 

Product Spotlight

iProbe - USB Phased Array Probe

Turn your PC, Laptop or Tablet into a powerful 32:64 Phased Array system with our USB powered Phas
...
ed Array iProbe and inspection software package. Perform affordable weld inspection and corrosion mapping inspections with this powerful but small system. The probe has a 100V pulser, 8K PRF, dual axis encoder input and achieves outstanding signal quality.
>

NovaScope 6000

The all-digital Novascope 6000 is a portable, ultra-high precision thickness gauge for high-speed
...
thickness measurement. Novascope 6000 has unmatched capabilities and unique features including: •Superior Resolution with high contrast, high-speed color RF display •High pulser voltage •Real-time video output •Increased internal/external data storage •Programmable SetUp features •Battery & AC Powered
>

NEW! The PragmaPro Instrument Platform

The PragmaPro is based on a modular cartridge technology and supports various NDT instrument modal
...
ities such as UT, PAUT, ECT and many more. This new platform is based on a machined, powder-coated aluminum frame for shock-proofness, best sealing qualities and maximum heat dissipation. This is practical to extend the outdoor temperature range and/or to extend the power injected in the transducers. The PragmaPro is aiming at a very wide range of applications, such as weld scanning, corrosion mapping and composite testing.
>

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window