where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

699 views
Technical Discussions
AxlZ W AekZ
R & D
King mongkut's university of technology Thonburi, Thailand, Joined Jun 2001, 16

AxlZ W AekZ

R & D
King mongkut's university of technology Thonburi,
Thailand,
Joined Jun 2001
16
08:21 Apr-13-2002
I have problem with MFL TOOL for wire rope inspection.

I build a MFL tool for wire rope inspecton with coil sensors inside and use electromagnet for magnetizing. A problem is heat when I apply current from battery about 100 A to magnetizing coil. Can I reduce the heat ? Becase of, it destroy my casing and sensors.


 
 Reply 
 
Michael Trinidad
Consultant,
LMATS Pty Ltd , Australia, Joined Jan 2003, 141

Michael Trinidad

Consultant,
LMATS Pty Ltd ,
Australia,
Joined Jan 2003
141
04:52 Apr-16-2002
Re: I have problem with MFL TOOL for wire rope inspection.
You could try laminating the magnetic cores of your coils similar to transformers.

But what may be of interest to you was initially MFL rope testers were AC magnetic field operated but to my knowledge could only detect LF (Local Faults) such as broken wires. However after the advent and utilization of powerful rare earth magnets MFL rope testers can detect LF and LMA (Loss of Magnetic Area) faults such as corrosion, wear, thinning etc using a combination of coil and hall effect sensors.


Kindest Regards


Michael Trinidad

: I build a MFL tool for wire rope inspecton with coil sensors inside and use electromagnet for magnetizing. A problem is heat when I apply current from battery about 100 A to magnetizing coil. Can I reduce the heat ? Becase of, it destroy my casing and sensors.
.



 
 Reply 
 
AxlZ W AekZ
R & D
King mongkut's university of technology Thonburi, Thailand, Joined Jun 2001, 16

AxlZ W AekZ

R & D
King mongkut's university of technology Thonburi,
Thailand,
Joined Jun 2001
16
07:31 Apr-17-2002
Re: I have problem with MFL TOOL for wire rope inspection.
: I build a MFL tool for wire rope inspecton with coil sensors inside and use electromagnet for magnetizing. A problem is heat when I apply current from battery about 100 A to magnetizing coil. Can I reduce the heat ? Becase of, it destroy my casing and sensors.
.
Dear Sir.
Thank you, for your suggest. I used DC supply(100A. 12V.)not AC supply. Because of,rare magnet in my country is expensive and hard to find. Can I detect LMA fault with coil sensors only? I think tested signal can intigral with sigal conditioning unit. Right?

THank you.

AxlZ W. AekZ




 
 Reply 
 
Michael Trinidad
Consultant,
LMATS Pty Ltd , Australia, Joined Jan 2003, 141

Michael Trinidad

Consultant,
LMATS Pty Ltd ,
Australia,
Joined Jan 2003
141
02:00 Apr-18-2002
Re: I have problem with MFL TOOL for wire rope inspection.
Sawadee,

I guess with new computing technology you may be able to differentiate between the signals. I have done a lot of rope testing on mineshafts in Australia and found it to be a very interesting field.

If I can help in anyway please ask.

Kindest Regards


Michael Trinidad
Business Development Manager




 
 Reply 
 

Product Spotlight

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

NOVO Armor 15 & NOVO Armor 22

The Armor Kit Contains the NOVO Armor, which provides additional mechanical protection to the NOVO 1
...
5WN & NOVO 22WN Detectors, the Armor Stand and a traveling soft cover. - Newest shock absorbent technology case - Water resistant design - Supports wired & wireless communication - Multiple positioning options - Tripod connection using the Built-in 1/4” threads - Simple Detector battery replacement
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window