where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1464 views
Technical Discussions
Arivazhagan
NDT Inspector,
HAL, India, Joined Oct 2014, 5

Arivazhagan

NDT Inspector,
HAL,
India,
Joined Oct 2014
5
10:25 Oct-30-2014
Shear wave reference block for Rings

Need to fabricate a reference standard (Acceptance critereia is 2mm ) for inspecting alumiium ring of size 1200mm OD, 1100mm ID and 90 mm thick , pl suggest.

 
 Reply 
 
Dent
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 250

Dent

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
250
12:02 Oct-30-2014
Re: Shear wave reference block for Rings
In Reply to Arivazhagan at 10:25 Oct-30-2014 (Opening).

It is normal to put notches ID & OD on the actual part for this type of inspection rather than make a special cal. block.

Your specification/procedure should be consulted.

 
 Reply 
 
Jawed Akhter
Jawed Akhter
16:23 Oct-30-2014
Re: Shear wave reference block for Rings
In Reply to Arivazhagan at 10:25 Oct-30-2014 (Opening).

Your stansard call for 2mm flat bottom hole of side drill hole ? in eithe case you need
reference block to set up sensitivity.

 
 Reply 
 
Dent
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 250

Dent

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
250
21:24 Oct-30-2014
Re: Shear wave reference block for Rings
In Reply to Jawed Akhter at 16:23 Oct-30-2014 .

Subject line of posting is Shear Wave. FBH's are almost always for straight beam. SDH's are normally used for weld inspections.
Notches are used for angle beam examinations of various product forms including large forged rings like you describe. Unless you have additional material to make a cal block from it is common to put the notches in the actual product and if necessary machine them off after testing.

1
 
 Reply 
 
Simon Amallraja
Consultant, Advanced NDT Methods
Anu Consultants, India, Joined Aug 2013, 38

Simon Amallraja

Consultant, Advanced NDT Methods
Anu Consultants,
India,
Joined Aug 2013
38
10:00 Nov-03-2014
Re: Shear wave reference block for Rings
In Reply to Arivazhagan at 10:25 Oct-30-2014 (Opening).

You have couple of Ref Standard manufuacturers with NIST trecebaility.

Check with www.phtools.com. They will be able to support you immediately.

Good Luck

 
 Reply 
 

Product Spotlight

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window