where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1234 views
Technical Discussions
jagan
Engineering,
Saudi Arabia, Joined Dec 2011, 23

jagan

Engineering,
Saudi Arabia,
Joined Dec 2011
23
09:02 Jan-08-2015
Acceptance criteria for surface ECT

Hi
Is there any criteria for surface ECT for acceptance and rejection.

Surface ECT with absolute probe technique on Inconnel625 meterial.

 
 Reply 
 
Mario Talarico
NDT Inspector,
Italy, Joined May 2010, 423

Mario Talarico

NDT Inspector,
Italy,
Joined May 2010
423
10:10 Jan-08-2015
Re: Acceptance criteria for surface ECT
In Reply to jagan at 09:02 Jan-08-2015 (Opening).

yes.
greetings
mario

 
 Reply 
 
jagan
Engineering,
Saudi Arabia, Joined Dec 2011, 23

jagan

Engineering,
Saudi Arabia,
Joined Dec 2011
23
11:02 Jan-08-2015
Re: Acceptance criteria for surface ECT
In Reply to Mario Talarico at 10:10 Jan-08-2015 .

Mr. Mario,

let me know the standard for this.

 
 Reply 
 
Mario Talarico
NDT Inspector,
Italy, Joined May 2010, 423

Mario Talarico

NDT Inspector,
Italy,
Joined May 2010
423
00:33 Jan-09-2015
Re: Acceptance criteria for surface ECT
In Reply to jagan at 11:02 Jan-08-2015 .

Jagan,
no.
Eddy current notche standard for flat surface (including surface round), bolt hole, but also pipes, are established for the production or in the service. For example AF specification, ASTM E 426, when matched with product specification, especially those of the main manufacturers of aircraft and avio turbine, where inconel,nickel alloys and titanium, are widely used. RR, MTU, Snecma, P & W, etc., have elaborated in detail their specifications to detect crack-like surface signals. Of course the scope is well defined.
Do not understand what you're handling. I suggest you retrieve and comply with the specifications of the product manufacturer to prevent improper application. Remains in your 'scope'.
greetings
mario

 
 Reply 
 
Nat
Nat
08:22 Jan-12-2015
Re: Acceptance criteria for surface ECT
In Reply to Mario Talarico at 00:33 Jan-09-2015 .

BS EN 1711 outlines that any indication found to be verified by MPI/ LPT,
Criteria will wary depending on what stage is the product like Mill , finishing(weld), in-service(SCC, fatigue) and applicable industry( Aero, nuclear,O&G)

Generally all liner indications are to be repaired.

Nat

 
 Reply 
 
Jagan
Engineering,
Saudi Arabia, Joined Dec 2011, 23

Jagan

Engineering,
Saudi Arabia,
Joined Dec 2011
23
08:31 Jan-12-2015
Re: Acceptance criteria for surface ECT
In Reply to Nat at 08:22 Jan-12-2015 .

NAT,

BS EN 1711 is to perform surface inspection on the welds.

 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Panther

M2M PANTHER is a phased-array equipment designed for both desktop and industrial applications, offer
...
ing unparalleled performance in a compact unit. It combines the speed required for industrial integrated Phased-Array Ultrasound (PAUT) solutions, with the most complete set of total focusing method (TFM) imaging techniques, making it the ultimate tool for R&D and procedure qualification.
>

Magnetic X-Ray Pipeline Crawler 6''-60''

Suitable to work in 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometer
...
s and provide the efficient inspection of the pipeline.
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window