where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

LECOEUR ELECTRONIQUE
The Specialist of electronics for ultrasonic testing.
1772 views
Technical Discussions
sandip
NDT Inspector,
India, Joined Dec 2014, 7

sandip

NDT Inspector,
India,
Joined Dec 2014
7
13:59 Apr-03-2015
PAUT

Dear Sir,
i need guidance regarding AWS D1.1 code.
sir, we can do PAUT lieu of RT by using AWS D1.1 code.







THANKS......

 
 Reply 
 
J Mark Davis
Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama, USA, Joined Mar 2000, 85

J Mark Davis

Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama,
USA,
Joined Mar 2000
85
20:52 Apr-03-2015
Re: PAUT
In Reply to sandip at 13:59 Apr-03-2015 (Opening).

Yes you can iaw paragraph 6.36 and 6.36 if you qualify your PA procedure and your personnel.

AWS D1.5 has adopted the new Annex K for Phased Array that I developed for the 2015 AWS if approved by AASHTO. Which should happen this year. I have presented to TAC which as far as I understand has approved the new Annex K.

I have developed a draft ballot for D1.1 to be review by D1Q. I will make the final presentation next week in Miami. But they say it will not make it until 2020 code.

BUT, under todays rules if the engineer of record approves Phased Array then you can if you follow 6.36 and 6.37.

Several companies have used PA successfully with engineering approval

We have qualified PA procedures and personnel for these entities.

Sincerely,

J. Mark Davis
Davis NDE, Inc.

 
 Reply 
 
SANDIP
NDT Inspector,
India, Joined Dec 2014, 7

SANDIP

NDT Inspector,
India,
Joined Dec 2014
7
14:26 Apr-04-2015
Re: PAUT
In Reply to J Mark Davis at 20:52 Apr-03-2015 .

Thanks for your valuable opening.
sir. I wont to make a calibration block. for paut pipe to pipe butt joint 4" pipe thickness is 13.5mm according to the DNV- OS-F101, sir i just wont know about reference reflector. what i have to make there. SDH/NOTCH.

 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1286

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1286
15:48 Apr-04-2015
Re: PAUT
In Reply to SANDIP at 14:26 Apr-04-2015 .

Sandip, you will need to specify which appendix in OS-F101 you are working to. Appendix D is for all NDT except automated UT of girth welds. Appendix E is for automated UT of girth welds. Appendix D is essentially the typical UT requirements and the description for procedures are found in DNV Classification note 7. Table D-1 in F101 provides the details of the requirements for the sensitivity calibration blocks. If automated UT (AUT) is planned for your project, DNV OS F101 "demands" a system qualification. You may use virtually any reference target sizes or shapes, but you must demonstrate reliability (with a 90|95 PoD) and you must quantify your sizing accuracy. The qualification process is described in Section H of Appendix E and invokes the requirements of DNV RP-118. You may find this process particularly demanding for sizing if using an ECA based acceptance criteria. Section H in Appendix E requires under sizing error tolerances giving less than or equal to 5% probability of under sizing be determined and used in relation to any ECA specified defect sizes.

 
 Reply 
 

Product Spotlight

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Navic - Steerable Modular Automated Scanner

The Navic is a modular, motorized, steerable scanner designed to carry multiple attachments used
...
in various scanning and inspection applications. The Navic is capable of weld scanning (girth welds and long seam welds), automated corrosion mapping, and tank scanning.
>

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window