where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ULTRASOUND INSTITUTE
The Ultrasound Institute can develop new advanced ultrasonic measurement, imaging and NDT techniques for non-conventional applications.
1104 views
Technical Discussions
Josip Vuk
Josip Vuk
01:52 Sep-08-2003
Aircraft weld incpection

I am a student at Faculty of Engineering and Naval Arhitecture in Zagreb. I am doing my final thesis and am looking for a Maintenance Manual or Component Repair and Overhaul Manual for any part of any type of any Boeing or Airbus aircraft, which defines inspection of welds (either steel or aluminum).
My intention is to simulate such a part in faculty`s labaratory (for I am unable to acquire a real-life part or documentation)and to perform prescribed radiografic (or ultrasonic) testing.
Materials can be on-line.


 
 Reply 
 
Joe Buckley
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 528

Joe Buckley

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
528
06:50 Sep-08-2003
Re: Aircraft weld incpection
in my experience there are very few critical welded joints in Aircraft structures. Mostly just used in ancilliary assemblies, In particular in Ducting (e.g thin wall stainless or alloy tubes) and in landing gear.

----------- Start Original Message -----------
: I am a student at Faculty of Engineering and Naval Arhitecture in Zagreb. I am doing my final thesis and am looking for a Maintenance Manual or Component Repair and Overhaul Manual for any part of any type of any Boeing or Airbus aircraft, which defines inspection of welds (either steel or aluminum).
: My intention is to simulate such a part in faculty`s labaratory (for I am unable to acquire a real-life part or documentation)and to perform prescribed radiografic (or ultrasonic) testing.
: Materials can be on-line.
------------ End Original Message ------------




 
 Reply 
 
Gary
Consultant
TWI, United Kingdom, Joined May 2001, 15

Gary

Consultant
TWI,
United Kingdom,
Joined May 2001
15
02:31 Sep-11-2003
Re: Aircraft weld incpection
From my experience I have seen some fairly bad accidents through failures of welds in ductings, particularly with secondary damge to wiring looms etc.

Landing gear also has its uses on occassion.

----------- Start Original Message -----------
: in my experience there are very few critical welded joints in Aircraft structures. Mostly just used in ancilliary assemblies, In particular in Ducting (e.g thin wall stainless or alloy tubes) and in landing gear.
: : I am a student at Faculty of Engineering and Naval Arhitecture in Zagreb. I am doing my final thesis and am looking for a Maintenance Manual or Component Repair and Overhaul Manual for any part of any type of any Boeing or Airbus aircraft, which defines inspection of welds (either steel or aluminum).
: : My intention is to simulate such a part in faculty`s labaratory (for I am unable to acquire a real-life part or documentation)and to perform prescribed radiografic (or ultrasonic) testing.
: : Materials can be on-line.
------------ End Original Message ------------




 
 Reply 
 
Carlos Valdecantos
Engineering
MTORRES, Ing., Spain, Joined May 2001, 9

Carlos Valdecantos

Engineering
MTORRES, Ing.,
Spain,
Joined May 2001
9
01:07 Sep-12-2003
Re: Aircraft weld incpection
AIRBUS is currently using welded stringers as an alternative to massive machinning of thick plates. Welding is carried out by high power laser.

Our company is the supplier of the automatic machines for this process. Please, refer to MTORRES web site.

Regards,

C. Valdecantos



 
 Reply 
 

Product Spotlight

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window