where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ULTRASOUND INSTITUTE
The Ultrasound Institute can develop new advanced ultrasonic measurement, imaging and NDT techniques for non-conventional applications.
1017 views
Technical Discussions
vengadesh
Engineering,
Tech Mahindra LTD, India, Joined Mar 2016, 4

vengadesh

Engineering,
Tech Mahindra LTD,
India,
Joined Mar 2016
4
13:03 Mar-29-2016
probe output

Dear sir,
I have one doubt ,please help. we have 60 degree probe the prespex shoe was thickness reduced, due to continuous friction . the output of probe wavelength was changed into 65 degree. how can i draw DAC.? for that what is the formula for that..?

 
 Reply 
 
joan pagnoul
Student,
Technifutur, Belgium, Joined Mar 2014, 7

joan pagnoul

Student,
Technifutur,
Belgium,
Joined Mar 2014
7
15:19 Mar-29-2016
Re: probe output
In Reply to vengadesh at 13:03 Mar-29-2016 (Opening).

I think that first, your probe is useless because if I remember norms says 60+/-2 degrees.
And to draw a DAC, methods never change and there is no formula

1
 
 Reply 
 
Csaba Hollo
,
Retired, Canada, Joined Feb 2010, 301

Csaba Hollo

,
Retired,
Canada,
Joined Feb 2010
301
23:29 Mar-29-2016
Re: probe output
In Reply to vengadesh at 13:03 Mar-29-2016 (Opening).

If the code allows you to work with an angle outside of the 60 degree+-, then your calibrations, including regenerating your DAC, must be redone.
Several things have changed, not just your angle, but also your index point and most likely sensitivity.

1
 
 Reply 
 
massimo carminati
Consultant, AUT specialist
IMG Ultrasuoni Srl, Italy, Joined Apr 2007, 691

massimo carminati

Consultant, AUT specialist
IMG Ultrasuoni Srl,
Italy,
Joined Apr 2007
691
19:37 Mar-30-2016
Re: probe output
In Reply to vengadesh at 13:03 Mar-29-2016 (Opening).

Most codes would not allow you to use such a drifted angle from standard. You should recondition the probe or the wedge by adding a new wear sole, but before that you should bring back the original wedge angle to the original value. I warmly not suggest to just use sand paper for doing this.

 
 Reply 
 

Product Spotlight

PROlineTOP Plug & Play Ultrasonic inspection device

As Plug & Play solution it units all control and operation elements in a small housing and therefo
...
re replaces the typical control cabinet...
>

YXLON Cougar EVO

Scalable small footprint X-ray inspection systems for assembly and laboratory applications. The
...
YXLON Cougar EVO series was designed to provide the "best-in- class" inspection solutions for SMT, semiconductor, and laboratory assembly applications, while maintaining a small system footprint for maximum convenience. With optimized software and hardware, these systems produce higher quality and more consistent results than other electronics inspection systems currently on the market.
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window