where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1870 views
Technical Discussions
sreejith
India, Joined Jan 2015, 5

sreejith

India,
Joined Jan 2015
5
02:21 Mar-11-2017
PAUT in Inconel cladding

Hai Experts,
Is PAUT possible for the following joints..

1)Volumetric examination and bond line integrity check in cladded area.

cladded Pipe OD/Material=24"/ API 5L X65
Cladding material & thickness=Inconel 625 & 4.3 mm thickness.
Is there any special Probe like DMA or DLA required?

2)Volumetric Examination in butt joint/similar welds

Butt joint= similar welds ,single 'V' between cladded pipe and cladded hanger flange.

 
 Reply 
 
Aniss Ziani
, Advanced NDT inspector
ISQ, Algeria, Joined Nov 2014, 32

Aniss Ziani

, Advanced NDT inspector
ISQ,
Algeria,
Joined Nov 2014
32
15:12 Mar-11-2017
Re: PAUT in Inconel cladding
In Reply to sreejith at 02:21 Mar-11-2017 (Opening).

Hi Sreejith,
Have a look on this interesting article from Carlo Romito and Frederic Jacques :
https://www.linkedin.com/pulse/method-automatic-ultrasonic-testing-aut-corrosion-resistant-romito-1
Regards,
Aniss Ziani

 
 Reply 
 
Anmol Birring
Consultant,
Birring NDE Center, Inc., USA, Joined Aug 2011, 820

Anmol Birring

Consultant,
Birring NDE Center, Inc.,
USA,
Joined Aug 2011
820
22:24 Mar-11-2017
Re: PAUT in Inconel cladding
In Reply to sreejith at 02:21 Mar-11-2017 (Opening).

what is the weld material ?

 
 Reply 
 
sreejith
India, Joined Jan 2015, 5

sreejith

India,
Joined Jan 2015
5
02:24 Mar-13-2017
Re: PAUT in Inconel cladding
In Reply to Anmol Birring at 22:24 Mar-11-2017 .

SMAW,E7018

 
 Reply 
 
Anmol Birring
Consultant,
Birring NDE Center, Inc., USA, Joined Aug 2011, 820

Anmol Birring

Consultant,
Birring NDE Center, Inc.,
USA,
Joined Aug 2011
820
05:48 Mar-13-2017
Re: PAUT in Inconel cladding
In Reply to sreejith at 02:24 Mar-13-2017 .

So it is carbon steel weld with A625 clad overlay ?

 
 Reply 
 
sreejith
India, Joined Jan 2015, 5

sreejith

India,
Joined Jan 2015
5
07:26 Mar-14-2017
Re: PAUT in Inconel cladding
In Reply to Anmol Birring at 05:48 Mar-13-2017 .

yes

 
 Reply 
 
Anmol Birring
Consultant,
Birring NDE Center, Inc., USA, Joined Aug 2011, 820

Anmol Birring

Consultant,
Birring NDE Center, Inc.,
USA,
Joined Aug 2011
820
04:19 Mar-16-2017
Re: PAUT in Inconel cladding
In Reply to sreejith at 07:26 Mar-14-2017 .

If the weld is CS, you can use PAUT - shear wave but limited to the 1/2 vee mode. So that will mean removal of weld cap to get full weld coverage. And since it is CS you can add TOFD

 
 Reply 
 

Product Spotlight

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

A1525 SOLO

A1525 Solo – the most compact and affordable TMF unit with two phased array transducers and 3D v
...
isualization and analysis software in standard delivery set. A compact, ergonomic and easy to handheld Phased Array unit based on Total Focusing Method for easy-going imaging of inspection objects with two-dimensional and three-dimensional visualization and evaluation of inspection results.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

CIVA 2020 UT Module

CIVA NDE Simulation Software is the world leader of NDT Simulation. The UT simulation Module incl
...
udes: - "Beam computation": Beam propagation simulation - "Inspection Simulation": Beam interaction with flaws or specimens The user can simulate a whole inspection process (pulse echo, tandem or TOFD) with a wide range of probes (conventional, Phased- arrays or EMAT), components, and flaws.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window