where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
687 views
Career Discussions
Scott McCready
Scott McCready
17:07 Dec-20-2018
Who can overturn a level II decision?

Hi, I was wondering if anyone can help me. Who in the workplace/job-site can overturn/overrule an interpretation of test results of a CGSB certified level II?

I was always lead to believe that it has to be either a level III or an engineer. If this is a case and someone other then them is overruling would there be any consequences if this was reported to the governing body.

I thank you in advance for any help.

Scott

 
 Reply 
 
krishna bharathi
NDT Inspector,
India, Joined Jun 2015, 15

krishna bharathi

NDT Inspector,
India,
Joined Jun 2015
15
18:49 Dec-20-2018
Re: Who can overturn a level II decision?
In Reply to Scott McCready at 17:07 Dec-20-2018 (Opening).

Hello,

The standards are always rule in the site,if the technician is decided something we get any doubt on that,surely we have to go for level 3,he will show how the standard will rule,

Hope that helps,

1
 
 Reply 
 
Shane Feder
, Quality Co-ordinator (SubSea)
Thailand, Joined Dec 2014, 89

Shane Feder

, Quality Co-ordinator (SubSea)
Thailand,
Joined Dec 2014
89
13:21 Dec-23-2018
Re: Who can overturn a level II decision?
In Reply to Scott McCready at 17:07 Dec-20-2018 (Opening).

Scott,
Anyone can overrule a Level II but the person doing it must be approved by the client/owner.

As an example, I may be the Clients Representative - I do not agree with a negative interpretation by a Level II.

I have a different Level II review and it is acceptable.

Remember, interpretation whether it is UT or RT is based on opinion.

If you are the one paying for the NDT and you do not agree with the interpretation (hopefully you have enough experience to be able to query the interpretation) then the best way forward is to call in the NDT companies Level III.
A bit more info may enable a better response,
Cheers,
Shane

1
 
 Reply 
 
Edgar Casanova
River Parishers Community Collage, USA, Joined Jan 2019, 4

Edgar Casanova

River Parishers Community Collage,
USA,
Joined Jan 2019
4
15:58 Jan-03-2019
Re: Who can overturn a level II decision?
In Reply to Scott McCready at 17:07 Dec-20-2018 (Opening).

NDT Interpretations can be overruled by the Source Inspector who represents the End User.
You do not have to change your interpretation, the Source Inspector can line through and sign and date his/her acceptance. When you have this happen to you, don't be too upset. The responsibility and lability shifts off your shoulders to the Source Inspector.

1 1
 
 Reply 
 

Product Spotlight

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

NDTkit RT

NDTkit RT, TESTIA's Digital Radiography software The NDTkit product line software for X-ray analysi
...
s. NDTkit RT is a software benefiting from the Ultis kernel which is dedicated to radiographic image analysis. It offers a set of tools and filtering processes to assist RT operators in finding relevant flaws.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window