where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

396 views
Technical Discussions
Ashwani Kumar
Engineering,
MIDHANI, Hyderabad, India, Joined Jun 2015, 96

Ashwani Kumar

Engineering,
MIDHANI, Hyderabad,
India,
Joined Jun 2015
96
08:51 May-10-2019
Helium Leak Test

Dear sir,
We are making helical part by bending 1 to 2 mm thick titanium tubes to the helical size of 300 mm.
We would like to carry out Helium Leak Test of the item.
I may be advised the testing technique & the required set up of the test.
Regards

 
 Reply 
 
William A Jensen
Other,
IHI Southwest Technologies, Inc., USA, Joined May 2017, 67

William A Jensen

Other,
IHI Southwest Technologies, Inc.,
USA,
Joined May 2017
67
16:14 May-10-2019
Re: Helium Leak Test
In Reply to Ashwani Kumar at 08:51 May-10-2019 (Opening).

I would suggest reading the ASM Handbook Volume 17 and also reviewing ASME Section V, Article 10. Then you may want to contact a company that provides these services and consult with them.

 
 Reply 
 
S V SWAMY
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S V SWAMY

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
17:51 May-10-2019
Re: Helium Leak Test
In Reply to Ashwani Kumar at 08:51 May-10-2019 (Opening).

If the product is MIDHANI's, why not check with your counterparts in NFC? They will be glad to help out I would think...

Swamy
Ex NFC QC / QA

 
 Reply 
 
parham mirfallah
Consultant,
Padideh Sazan Iranian azma, Iran, Joined Sep 2014, 9

parham mirfallah

Consultant,
Padideh Sazan Iranian azma,
Iran,
Joined Sep 2014
9
14:12 Jun-20-2019
Re: Helium Leak Test
In Reply to Ashwani Kumar at 08:51 May-10-2019 (Opening).

Dear sir
As you want to do helium test you must know the all strps as respons time and cleaning time to do it best but befor that you'd beter to leak test with lower sensivity

Best regard
Parham

 
 Reply 
 

Product Spotlight

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

GUL Subsea Solutions - Screeening & Monitoring

To inspect new and existing subsea lines, you need proven technology and experience. GUL offers it's
...
technology to solve this challenge: GUL Subsea and gMAT Transducer Rings.
>

Echomac® PA Tube Weld Tester

The new robotic Echomac® PA TW is an operator friendly test system for detecting weld zone defects
...
in tube and pipe caused by scarfing or welding processes. Electronic scanning ensures that the entire weld zone is covered without the need for mechanical movement or operator adjustment.
>

Ultrasonic Probe Recharacterization Service

NDT Systems offers a comprehensive Aftercare and Recharacterization Service for all our ultrasonic
...
probes. The Recharacterization Service is fully compliant with International ASTM E1065 Standard Guide (and other applicable standards) and offers complete documentation, traceable to the ASTM E1065 Standard. For more details or to schedule Recharacterization Services contact ndtsales@ndtsystems.com
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window