where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Iris Inspection Services, Inc.
We are the world's largest supplier of air cooler, boiler and exchanger tubing inspection services.
1267 views
Technical Discussions
Rich Roberts
Engineering, Executive Managment
Quest Integrity Group, USA, Joined Nov 1998, 78

Rich Roberts

Engineering, Executive Managment
Quest Integrity Group,
USA,
Joined Nov 1998
78
08:21 Oct-02-2004
Transducer Wear Face

We have designed a piece of ultrasonic equipment housing numerous (64) ultrasonic compression transducers. This equipment is exposed to a very harsh environment. Recently we have noticed that a lot of the transducer wear faces have been worn off, exposing a silver metallic material. The transducer continues to perform properly, however we are concerned with degradation of the signal quality if the silver metallic material were to become damaged. Could someone recommend a repair method (preferable some type of adhesive) which we can apply to the transducers front face? We have tried various types of epoxy, however this material tends to attenuate the signal below acceptable levels. Any recommendations would be greatly appreciated.



 
 Reply 
 
N.Kuppusamy
Consultant, NDT Level-III Engineer
Advanced Inspection & Testing (S) Pte Ltd, Singapore, Joined Dec 2003, 34

N.Kuppusamy

Consultant, NDT Level-III Engineer
Advanced Inspection & Testing (S) Pte Ltd,
Singapore,
Joined Dec 2003
34
04:10 Oct-03-2004
Re: Transducer Wear Face
Hi Mr.Rich Roberts,
Why don't you experiment with some metal (stainless steel, etc) wear faces. It may prove to be beneficial in many fronts such as improving coupling efficiency, Excellent wear resistance. You may design it as a detachable attachment (threading mechnism)on regular probe design. You may encounter problems with high thermal conductivity of metals, and I think it can be resolved by experiment and improving design.
Best Regards,
N.Kuppusamy

----------- Start Original Message -----------
: We have designed a piece of ultrasonic equipment housing numerous (64) ultrasonic compression transducers. This equipment is exposed to a very harsh environment. Recently we have noticed that a lot of the transducer wear faces have been worn off, exposing a silver metallic material. The transducer continues to perform properly, however we are concerned with degradation of the signal quality if the silver metallic material were to become damaged. Could someone recommend a repair method (preferable some type of adhesive) which we can apply to the transducers front face? We have tried various types of epoxy, however this material tends to attenuate the signal below acceptable levels. Any recommendations would be greatly appreciated.
------------ End Original Message ------------




 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1286

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1286
06:32 Oct-03-2004
Re: Transducer Wear Face
Rich:
The wear face is generally a quarterwave matchplate. This is an attempt to match impedance and provide a constructive interference on the forward moving pulse. I suggest you contact a local probe manufacturer for help selecting the best options which are usually boron silicates. Sigma transducers are located in Washington;
Kennewick, WA 99336
Phone: (509) 783-9497
Fax: (509) 783-9655
Email: info@sigmatx.com

Regards
Ed

----------- Start Original Message -----------
: We have designed a piece of ultrasonic equipment housing numerous (64) ultrasonic compression transducers. This equipment is exposed to a very harsh environment. Recently we have noticed that a lot of the transducer wear faces have been worn off, exposing a silver metallic material. The transducer continues to perform properly, however we are concerned with degradation of the signal quality if the silver metallic material were to become damaged. Could someone recommend a repair method (preferable some type of adhesive) which we can apply to the transducers front face? We have tried various types of epoxy, however this material tends to attenuate the signal below acceptable levels. Any recommendations would be greatly appreciated.
------------ End Original Message ------------





 
 Reply 
 
Doug Breeze
Director, Consultant; R&D
Inspection Software Limited, United Kingdom, Joined May 2000, 20

Doug Breeze

Director, Consultant; R&D
Inspection Software Limited,
United Kingdom,
Joined May 2000
20
02:17 Oct-03-2004
Re: Transducer Wear Face
Hi Rich,
Try three (or maybe four) wear pins located at the extremeties of the array or its holder, with a couplant gap of y/4 (in the couplant). This should eliminate abrasion, allow for minor contour changes, and with sufficient flow will give more consistent coupling.
Doug
---------- Start Original Message -----------
: We have designed a piece of ultrasonic equipment housing numerous (64) ultrasonic compression transducers. This equipment is exposed to a very harsh environment. Recently we have noticed that a lot of the transducer wear faces have been worn off, exposing a silver metallic material. The transducer continues to perform properly, however we are concerned with degradation of the signal quality if the silver metallic material were to become damaged. Could someone recommend a repair method (preferable some type of adhesive) which we can apply to the transducers front face? We have tried various types of epoxy, however this material tends to attenuate the signal below acceptable levels. Any recommendations would be greatly appreciated.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

NovaScope 6000

The all-digital Novascope 6000 is a portable, ultra-high precision thickness gauge for high-speed
...
thickness measurement. Novascope 6000 has unmatched capabilities and unique features including: •Superior Resolution with high contrast, high-speed color RF display •High pulser voltage •Real-time video output •Increased internal/external data storage •Programmable SetUp features •Battery & AC Powered
>

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window