where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
620 views
Technical Discussions
Nikos Roussos
Greece, Joined Aug 2019, 2

Nikos Roussos

Greece,
Joined Aug 2019
2
21:33 Sep-01-2019
PAUT inspection of thick welds
zoom image

weld

Dear experts,
I‘ve been asked if I can inspect properly welded pipes with thickness of 90mm.
The equipment that I have is a Sonatest Prisma 16:64 with X3-PE-5.0M64E0.6P 64 element probe. I will also use a weld scanner from Phoenix.
Do you think my equipment is capable of giving me reliable results in such thick welds with the geometry shown in the figure? Do you think I should get a sensor with less frequency (2,25 or 3,5 MHz)?
Additional to PAUT inspection I will also perform TOFD, but my main concerns are for the PAUT.

 
 Reply 
 
Creed
NDT Inspector,
Vietnam, Joined Jul 2009, 34

Creed

NDT Inspector,
Vietnam,
Joined Jul 2009
34
06:15 Sep-02-2019
Re: PAUT inspection of thick welds
In Reply to Nikos Roussos at 21:33 Sep-01-2019 (Opening).

First of all, the inspection should be performed following the standard and acceptance criteria or your company procedure writing; follow the standard, I am pretty sure you will have the answer YES or NO for your question.
My opinion you need to conduct the inspection with multi scans to cover entire the weld body, however based on the sketch of weld configuration the bevel angle should be concerned as a limitation, due to oriental of the fusion face defects wouldn't give the good refection with the PAUT sectorial beam.

1
 
 Reply 
 
Elias Campanario
Engineering,
Tecnicas Reunidas, Spain, Joined Oct 2013, 3

Elias Campanario

Engineering,
Tecnicas Reunidas,
Spain,
Joined Oct 2013
3
10:22 Sep-02-2019
Re: PAUT inspection of thick welds
In Reply to Nikos Roussos at 21:33 Sep-01-2019 (Opening).

Dear Nikos;

Regarding your question, in my opinion, the best solution in your case would be to combine inspection by ToFD and PAUT.

In any case, you should make a mock up with notches in the welding bevel, in which to test the scan plan that you generate for the inspection.

As for the PAUT probes, maybe for that thickness you need a 3.5 or 2.25 MHz probe.
With the 5MHz probe, maybe you to have a lot of noise at great depth.

I hope I've helped.

1
 
 Reply 
 
Ali
NDT Inspector,
Iran, Joined Mar 2013, 111

Ali

NDT Inspector,
Iran,
Joined Mar 2013
111
15:39 Sep-02-2019
Re: PAUT inspection of thick welds
In Reply to Nikos Roussos at 21:33 Sep-01-2019 (Opening).

this bevel configuration is not suitable for PAUT Sectorial scan but you can apply Tofd for better detection of side wall defect.If you have access to inside of vessel,perform Tofd and PAUT scan from out side and inside ( only half skip for PAUT) .this technique will reduce tofd dead zone only in backwall area and for PAUT will reduce sound path and increase signal to nois ratio in half skip instead of full skip scan.
Hope material grains is fine and surface is not wrought for PAUT and Tofd inspection.

1
 
 Reply 
 
laurie
Australia, Joined Feb 2019, 36

laurie

Australia,
Joined Feb 2019
36
02:35 Sep-03-2019
Re: PAUT inspection of thick welds
In Reply to Nikos Roussos at 21:33 Sep-01-2019 (Opening).

If you're going to be doing more of this type of work I'd suggest your boss might have to stump up for some simulation software.

Use a simulator like UTMan which from memory is something like 100 Euro and does manual UT, TOFD and AUT.
http://www.utsim.co.uk/index.html

If you have a couple of thousand dollars then Beamtools will do everything and also has sectorial beamset beam energy display which would be a big help for your long beam paths.
https://www.eclipsescientific.com/beamtool.html

There are lots of others including Olympus NDT SetupBuilder
https://www.olympus-ims.com/en/omniscan-software/#!cms[tab]=%2Fomniscan-software%2Fndt-setupbuilder

 
 Reply 
 

Product Spotlight

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window