where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1572 views
Technical Discussions
flo
flo
02:14 Feb-06-2005
NDE for helicopter rotor blades

Hello,
I've got a problem.
I have to come up with a in-service NDE system which should check 12 rotor blades per week.
My rotor blade is made by a leading edge of solid CFRP with heater strip and erosion shield adhesively bonded. The rest of the structure is a non-metallic honeycomb (Nomex) with GFRP layers.
I have to detect delaminations on the solid CFRP; disbonds between CFRP, heater strip and erosion shield; and finally skin-core disbonds and region of crushed core.

I'm concerned due to the fact low frequency methods tend to work quite well with honeycomb and composite skins. But for the monolithic CFRP?
I guess some ultrasonic technique, multi array probe for instance, can do an overall good job but the whole process would be rather slow.

Thanks for your advice,

Floriano.


 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 307

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
307
02:56 Feb-07-2005
Re: NDE for helicopter rotor blades
----------- Start Original Message -----------
: Hello,
: I've got a problem.
: I have to come up with a in-service NDE system which should check 12 rotor blades per week.
: My rotor blade is made by a leading edge of solid CFRP with heater strip and erosion shield adhesively bonded. The rest of the structure is a non-metallic honeycomb (Nomex) with GFRP layers.
: I have to detect delaminations on the solid CFRP; disbonds between CFRP, heater strip and erosion shield; and finally skin-core disbonds and region of crushed core.
: I'm concerned due to the fact low frequency methods tend to work quite well with honeycomb and composite skins. But for the monolithic CFRP?
: I guess some ultrasonic technique, multi array probe for instance, can do an overall good job but the whole process would be rather slow.
: Thanks for your advice,
: Floriano.
------------ End Original Message ------------


Dear Floriano,

NDT Consultants in the United Kingdom may be able to help you.

We have a research department, and they are just finishing a project looking at in-service (and in manufacturing) inspection of all types of Aerospace Composites.

One of the developments that has come our of this is N-BUS which we hope to have commercially available "within a few weeks". This is a C-Scan Narrow Band Ultrasonic Spectroscopy.

Alternatively, we are working with a research organisation in the USA developing an Ultrasonic Camera. This permits an almost real time (typically 1 to 2 seconds) image to be captured from immersion ultrasonics, covering an area of about 50mm x 50mm. They are also working on developments for larger areas of view, and also single sided inspection.

A third area is Digital Radiography, where very low X-Ray voltages can produce some high resolution X-Ray images.

Please get in touch with some more details, and we will see how we can cooperate with you.

Regards,

Godfrey Hands



 
 Reply 
 
Jens Forker
Jens Forker
02:17 Feb-07-2005
Re: NDE for helicopter rotor blades
Hello Floriano,

AE (acoustic emission) might be good tool for a check of the rotor blades. It requires loading of the blade but may provide a reasonable quick inspection of your blades.
If you are interested contact me for more information.
regards
Jens

----------- Start Original Message -----------
: Hello,
: I've got a problem.
: I have to come up with a in-service NDE system which should check 12 rotor blades per week.
: My rotor blade is made by a leading edge of solid CFRP with heater strip and erosion shield adhesively bonded. The rest of the structure is a non-metallic honeycomb (Nomex) with GFRP layers.
: I have to detect delaminations on the solid CFRP; disbonds between CFRP, heater strip and erosion shield; and finally skin-core disbonds and region of crushed core.
: I'm concerned due to the fact low frequency methods tend to work quite well with honeycomb and composite skins. But for the monolithic CFRP?
: I guess some ultrasonic technique, multi array probe forinstance, can do an overall good job but the whole process would be rather slow.
: Thanks for your advice,
: Floriano.
------------ End Original Message ------------




 
 Reply 
 
Jörg Collrep
Jörg Collrep
05:50 Feb-09-2005
Re: NDE for helicopter rotor blades
Hello Floriano,
have you ever tried to use Shearography for these tests. It might be worth to do this but it depends on the depth of the defects you are looking for. If you are interested in this technology or maybe would like to see a demo please contact me to discuss further details.
Rgds
Jörg


: : Hello,
: : I've got a problem.
: : I have to come up with a in-service NDE system which should check 12 rotor blades per week.
: : My rotor blade is made by a leading edge of solid CFRP with heater strip and erosion shield adhesively bonded. The rest of the structure is a non-metallic honeycomb (Nomex) with GFRP layers.
: : I have to detect delaminations on the solid CFRP; disbonds between CFRP, heater strip and erosion shield; and finally skin-core disbonds and region of crushed core.
: : I'm concerned due to the fact low frequency methods tend to work quite well with honeycomb and composite skins. But for the monolithic CFRP?
: : I guess some ultrasonic technique, multi array probe for instance, can do an overall good job but the whole process would be rather slow.
: : Thanks for your advice,
: : Floriano.
------------ End Original Message ------------




 
 Reply 
 
Simon Amallraja
Director
PET Aviation Systems P Ltd, India, Joined Jul 2003, 20

Simon Amallraja

Director
PET Aviation Systems P Ltd,
India,
Joined Jul 2003
20
02:54 Feb-13-2005
Re: NDE for helicopter rotor blades
----------- Start Original Message -----------
: : Hello,
: : I've got a problem.
: : I have to come up with a in-service NDE system which should check 12 rotor blades per week.
: : My rotor blade is made by a leading edge of solid CFRP with heater strip and erosion shield adhesively bonded. The rest of the structure is a non-metallic honeycomb (Nomex) with GFRP layers.
: : I have to detect delaminations on the solid CFRP; disbonds between CFRP, heater strip and erosion shield; and finally skin-core disbonds and region of crushed core.
: : I'm concerned due to the fact low frequency methods tend to work quite well with honeycomb and composite skins. But for the monolithic CFRP?
: : I guess some ultrasonic technique, multi array probe for instance, can do an overall good job but the whole process would be rather slow.
: : Thanks for your advice,
: : Floriano.
:
: Dear Floriano,
: NDT Consultants in the United Kingdom may be able to help you.
: We have a research department, and they are just finishing a project looking at in-service (and in manufacturing) inspection of all types of Aerospace Composites.
: One of the developments that has come our of this is N-BUS which we hope to have commercially available "within a few weeks". This is a C-Scan Narrow Band Ultrasonic Spectroscopy.
: Alternatively, we are working with a research organisation in the USA developing an Ultrasonic Camera. This permits an almost real time (typically 1 to 2 seconds) image to be captured from immersion ultrasonics, covering an area of about 50mm x 50mm. They are also working on developments for larger areas of view, and also single sided inspection.
: A third area is Digital Radiography, where very low X-Ray voltages can produce some high resolution X-Ray images.
: Please get in touch with some more details, and we will see how we can cooperate with you.
: Regards,
: Godfrey Hands
------------ End Original Message ------------

Dear Friend,

You can contact NDT Solutions at UK. They have a real time UT system called Rapidscan - which may be suitable to the application mentioned and you can do the scanning very fast. The data gives A scan, B Scan & C Scan of the component.

Contact Mr. Chris Kirby for more details.

Regards.
Amallraja.


 
 Reply 
 
agni
agni
09:43 Aug-25-2005
helicopter rotor blades
give some specifications to build the toy helicopter rotor blades


 
 Reply 
 

Product Spotlight

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

OPBOX with standard software is able to do all types of inspections and measurements: flaw detection in welds and materials, scanning of objects, testing composite materials, forged and moulded pieces, many UT inspections, measurements of properties of ma

Typical applications: UT measurements with pulse technique, Measurement of thicknesses also at hig
...
h temperatures, Measurements of properties of materials, including fluids and gases We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
>

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window