where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ZETEC, Inc.
Zetec is a global leader in nondestructive testing (NDT) solutions for the critical inspection needs of industries the world counts on every day, ...
949 views
Technical Discussions
Mike
Mike
07:32 Nov-25-2006
Exposure with Cobalt 60

Is a 16 curie colbalt source strong enough to shoot a 28" diameter 3" thick weld using a double wall exposure single wall viewing technique?


 
 Reply 
 
Anandam
Engineering, - DyGM - Operations & Reliability
Air Liquide India Limited, India, Joined Oct 2001, 13

Anandam

Engineering, - DyGM - Operations & Reliability
Air Liquide India Limited,
India,
Joined Oct 2001
13
07:04 Nov-26-2006
Re: Exposure with Cobalt 60
It hardly matter with the strength of the source as you need to give more exposure time. As far as the three inch double wall is concerned it can work as Cobalt 60 can penetrate up to 180 mm thick of steel. You can see the calculation chart for the same for particular film used.


----------- Start Original Message -----------
: Is a 16 curie colbalt source strong enough to shoot a 28" diameter 3" thick weld using a double wall exposure single wall viewing technique?
------------ End Original Message ------------




 
 Reply 
 
DJ Kallhof
DJ Kallhof
02:55 Nov-27-2006
Re: Exposure with Cobalt 60
You might want to check your Ug requirement before you attempt this time consuming endeavor. Unless your physical source size is .186" (4.7244mm) or less your geometric unsharpness will be over .020" (0.508mm). That low a power source will require a faster film and possibly salt screens which will decrease sensitivity. I would look to see if the customer thought ahead and installed a port for a "J" tube.
----------- Start Original Message -----------
: Is a 16 curie colbalt source strong enough to shoot a 28" diameter 3" thick weld using a double wall exposure single wall viewing technique?
------------ End Original Message ------------




 
 Reply 
 
DJ Kallhof
DJ Kallhof
03:16 Nov-27-2006
Re: Exposure with Cobalt 60
I must apologize. I knew I was wrong as soon as I closed the first reply. I calculated the total diameter rather than from the front face of the opposite wall. Your source size will have to be .166" (4.216mm) or less.
----------- Start Original Message -----------
: You might want to check your Ug requirement before you attempt this time consuming endeavor. Unless your physical source size is .186" (4.7244mm) or less your geometric unsharpness will be over .020" (0.508mm). That low a power source will require a faster film and possibly salt screens which will decrease sensitivity. I would look to see if the customer thought ahead and installed a port for a "J" tube.
: : Is a 16 curie colbalt source strong enough to shoot a 28" diameter 3" thick weld using a double wall exposure single wall viewing technique?
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

NDTkit RT

NDTkit RT, TESTIA's Digital Radiography software The NDTkit product line software for X-ray analysi
...
s. NDTkit RT is a software benefiting from the Ultis kernel which is dedicated to radiographic image analysis. It offers a set of tools and filtering processes to assist RT operators in finding relevant flaws.
>

Wireless TOFD scanner

Quick, accurate and highly reproducible welds testing. The System operates wirelessly and is compat
...
ible with any type of Windows based Laptop, Desktop or Tablet.
>

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window