where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
373 views
Technical Discussions
John
John
04:03 Nov-30-2006
Re: why TOFD cursor is parabola?

Hello Ed Ginzel;
But the guys use two phase array probes with shear wave wedge, the wedge is designed to generate 45degree shear wave, the angle is larger than the first critical angle, I don't think that it can generate Longitudinal wave in the sample, but conventional TOFD use LW, so I want to know can we use phase array probes with shear wave wedge to do TOFD technology?
Thank you!

----------- Start Original Message -----------
: Yun Xi
: Once a phased array generated pulse leaves the wedge it is not significantly different from a pulse made using a single element. If the phased array probe aperature is the same as a single element then the beam characteristics are the same.
: Phased array generated TOFD provides "convenience" to some users. It is often useful to have TOFD information even when doing a weld inspection with pulse-echo techniques; e.g. using Electronic raster scans (E-scans0 or sectorial (S-scans). This allows the operator a fast method of determining if the pulse-echo signal originates from a geometric condition or from a real flaw.
: But there are limits. If you want to just do a TOFD examination (without the phased array pulse-echo) you could design a multi zone TOFD technique with different frequency probes to optimise results. e.g. a 3mm diameter 15MHz TOFD probe for the upper 10mm of a weld inspection and a 5MHz 6mm diameter probe for the lower regions. Phased array generated TOFD would not have the ability to provide the improved upper zone coverage as its frequency is fixed. Also, there may be physical restrictions of the Phased Array probe wedge limiting the approach of the wedge to the weld cap. This may prevent optimum PCS being achieved.
: In spite of the limitations, I have seen some TOFD generated by phased array that is superior to some of the single element TOFD being provided by others on similar projects.
: It works the other way around too.
: It is often useful to have pulse-echo information when doing a TOFD technique. TOFD when used as a single pass D-scan does not provide information about which side of a weld a flaw occurs. You could do offset TOFD or even B-scan TOFD to determine the side of the weld a nonfusion was occurring by this may not be an option if the weld cap is left on and presents a scanning restriction. But pulse-echo can provide the information quickly. It is all the more convenient if this can be done using a single pass with a pair of phased array probes
: Regards
: Ed
: : Some guys use two phase array probe as TOFD,would you like tell me that is there any differene between typical TOFD?
: : Thank you for your reply.
: :
: : : YunXi:
: : : Typically TOFD uses a relatively small diameter element. The pressure boundary of such a probe can be approximated by a cone. Now imagine passing such a cone past a small point diffractor in its path. The point will first be detected far away as the edge of the cone detects the flaw. As the probe is moved along its straight scan path the flaw gets closer untilthe flaw is directly across from the probe. As the probe continues its scan movement past the flaw the process reverses and the flaw gets further away. The effect is like taking a slice through the cone. If you were to cut a cone at some point parallel to the central axis the remaining cross section is the definition of a parabola!
: : : The actual shape of the beam boudary is defeined by a Bessel function but the effect is effectively the same as a cone.
: : : The same effect can be seen on the shape of small targets in pulse-echo but the process is called backscatter instead of TOFD (forward scatter).
: : : Ed
: : :
: : : : I want to know why TOFD cursor is parabola?and what decide the parameter of the curve?is there any equation?Thanks a lot
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

A1525 SOLO

A1525 Solo – the most compact and affordable TMF unit with two phased array transducers and 3D v
...
isualization and analysis software in standard delivery set. A compact, ergonomic and easy to handheld Phased Array unit based on Total Focusing Method for easy-going imaging of inspection objects with two-dimensional and three-dimensional visualization and evaluation of inspection results.
>

AMIGO2

TSC Amigo2 - ACFM technology has developed a solid reputation for accurately detecting and sizing
...
surface-breaking cracks through paint and coatings. As the industry demands increased performance in speed, signal quality, and portability, it’s time for an evolution. It’s time for Amigo2.
>

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window