where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
780 views
Technical Discussions
Paulo
Paulo
09:40 Nov-30-2006
TOFD 190mm thickness!

Hey! Hello!
Anybody here have already inspected a weld with 190mm thickness using TOFD technique? What is the appropriate configuration?? Probes frequency, how many probes, and so on...
Thank you!



 
 Reply 
 
John
John
02:39 Dec-01-2006
Re: TOFD 190mm thickness!
I think maybe you need divide 190mm into three zones,upper 10mm can use 10MHz,zone from 10mm to 50mm can use 5MHz,and the residual zone can use 2.25MHz.
Maybe Ed Ginzel can give us some advise about this project or correct me!

----------- Start Original Message -----------
: Hey! Hello!
: Anybody here have already inspected a weld with 190mm thickness using TOFD technique? What is the appropriate configuration?? Probes frequency, how many probes, and so on...
: Thank you!
------------ End Original Message ------------




 
 Reply 
 
Udo Schlengermann
Consultant, -
Standards Consulting, Germany, Joined Nov 1998, 180

Udo Schlengermann

Consultant, -
Standards Consulting,
Germany,
Joined Nov 1998
180
00:33 Dec-04-2006
Re: TOFD 190mm thickness!
Hello,

Perhaps you can follow existing standards:

European Technical Specification
CEN/TS 14751:2004
Welding - Use of time-of-flight diffraction technique (TOFD) for examination of welds

gives detailed recommendations for butt weld thickness up to 300 mm.
E.g. for thickness between 100 mm and 200 mm: (at least) 3 depth zones 60 mm, 60 mm to 125 mm, 125 mm to 190 mm.
Test frequencies between 5 MHz and 2 MHz, depending on material properties.

Kind regards

Udo Schlengermann
GE Inspection Technologies GmbH
Huerth, Germany

----------- Start Original Message -----------
: I think maybe you need divide 190mm into three zones,upper 10mm can use 10MHz,zone from 10mm to 50mm can use 5MHz,and the residual zone can use 2.25MHz.
: Maybe Ed Ginzel can give us some advise about this project or correct me!
: : Hey! Hello!
: : Anybody here have already inspected a weld with 190mm thickness using TOFD technique? What is the appropriate configuration?? Probes frequency, how many probes, and so on...
: : Thank you!
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

Aerospace Systems - Automated Ultrasonic Inspection

USL are specialists in the design and manufacture of turnkey ultrasonic inspection systems for aer
...
ospace applications. From monolithic composites to complex honeycomb structures. This video shows just a few examples of what is possible, find out more at: www.ultrasonic-sciences.co.uk
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window