where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Materials Research Institute
Consulting to the NDT industry.
6528 views
Technical Discussions
Sunny
Sunny
02:20 Jan-17-2007
Ultrasonic Testing of Round Bars

Just want to make sure with experienced friends that only right way to look for defects inside the round bars volumetrically is to do longitudinal straight beam inspection. Shear wave is going to be good for certain depth only as it is refracted away from the center( depending on diameter). So only outer ring of certain depth( depending on diameter and refracted angle) can be inspected by shear wave.
Please comment.


 
 Reply 
 
Nigel
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
06:58 Jan-18-2007
Re: Ultrasonic Testing of Round Bars
Hello Sunny

The most common defect in round bars are "stringers", elongated non-metallic inclusions. These may be detected using a compression wave probe from the O.D. and scanning around the circumference and along the bar's whole length. Make certain that you have good overlap between successive circumferential scans so that the complete volume is completely covered. You can also monitor for a relatively stable backwall response. Any areas where the backwall response changes significantly should be carefully examined.

I cannot see the value in shearwave inspection of a round bar unless you scan along the length looking for opposite-side surface-breaking defects.

Do you not have a procedure and acceptance criteria for this work?


----------- Start Original Message -----------
: Just want to make sure with experienced friends that only right way to look for defects inside the round bars volumetrically is to do longitudinal straight beam inspection. Shear wave is going to be good for certain depth only as it is refracted away from the center( depending on diameter). So only outer ring of certain depth( depending on diameter and refracted angle) can be inspected by shear wave.
: Please comment.
------------ End Original Message ------------




 
 Reply 
 
Rajesh Bose
Engineering, NDT Engineer
BP, USA, Joined Aug 2001, 3

Rajesh Bose

Engineering, NDT Engineer
BP,
USA,
Joined Aug 2001
3
06:24 Jan-18-2007
Re: Ultrasonic Testing of Round Bars
Navi,

The only way to find out volumetric flaws is using straight beam inspection. You can inspect along the circumference with proper overlapand also from the ends of the pipe. Make sure you use the right probe diameter and frequency ( to lessen the beam spread). There is no need for shear wave inspection.Be careful about the mode converted signals.



 
 Reply 
 
Navi
Navi
06:39 Jan-18-2007
Re: Ultrasonic Testing of Round Bars
----------- Start Original Message -----------
: Navi,
: The only way to find out volumetric flaws is using straight beam inspection. You can inspect along the circumference with proper overlapand also from the ends of the pipe. Make sure you use the right probe diameter and frequency ( to lessen the beam spread). There is no need for shear wave inspection.Be careful about the mode converted signals.
------------ End Original Message ------------

Thanks Raj



 
 Reply 
 
Sunny
Sunny
08:07 Jan-18-2007
Re: Ultrasonic Testing of Round Bars
----------- Start Original Message -----------
: Hello Sunny
: The most common defect in round bars are "stringers", elongated non-metallic inclusions. These may be detected using a compression wave probe from the O.D. and scanning around the circumference and along the bar's whole length. Make certain that you have good overlap between successive circumferential scans so that the complete volume is completely covered. You can also monitor for a relatively stable backwall response. Any areas where the backwall response changes significantly should be carefully examined.
: I cannot see the value in shearwave inspection of a round bar unless you scan along the length looking for opposite-side surface-breaking defects.
: Do you not have a procedure and acceptance criteria for this work?
:
: : Just want to make sure with experienced friends that only right way to look for defects inside the round bars volumetrically is to do longitudinal straight beam inspection. Shear wave is going to be good for certain depth only as it is refracted away from the center( depending on diameter). So only outer ring of certain depth( depending on diameter and refracted angle) can be inspected by shear wave.
: : Please comment.
------------ End Original Message ------------

Thanks for great advise Sir, yes we have procedure and acceptence criteria



 
 Reply 
 
Thomas F. Murphy
NDT Inspector
USA, Joined Jul 2000, 16

Thomas F. Murphy

NDT Inspector
USA,
Joined Jul 2000
16
03:00 Jan-18-2007
Re: Ultrasonic Testing of Round Bars
Hello all,

In my experience large solid steal cyldinders are generall inspected radially from the OD. Angles of small variance ~15 degrees may be used to aid detection on unlikely, but possible flaws not globular or solid in shape. Consideration must be given to sought flaw size, metal path, and material attenuation. Often high output pulser voltages as well as proper understanding of received frequency are necessary for repeated estimating a reflectors size. There is an ASTM procedural guide written my Mr George Wheeler of General Electric Company. I do not recall the number. Most end users of such large pieces of metal have highly defined procedures mich must be used for conformance to contracts.

T



 
 Reply 
 
Ingolf Hertlin
Ingolf Hertlin
09:30 Jan-19-2007
Re: Ultrasonic Testing of Round Bars
Hi,
there is another method to test for volumetrical defects: Acoustic Resonance Testing. You do not need in advance where the defects might be. The part is excited by an impulse, e. g. a hit. You can measure the induced langitudinal and transversal waves using a microphone in the sonic and ultrasonic range (up to 50 kHz) or on the surface with a laser vibrometer. With round bars we do two or three measurements under a certain angle to analyse certain effects on resonance frequencies.
This method is a comparative one and not useful for a single specimen, more used in mass production. The results are temperature and dimension dependent. Both dependencies can be compensated automatically. If you need more information you can download this from www.rte.de or www.rte-acoustics.com.
Best regards
Ingolf
----------- Start Original Message -----------
: Just want to make sure with experienced friends that only right way to look for defects inside the round bars volumetrically is to do longitudinal straight beam inspection. Shear wave is going to be good for certain depth only as it is refracted away from the center( depending on diameter). So only outer ring of certain depth( depending on diameter and refracted angle) can be inspected by shear wave.
: Please comment.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

NEOS III

NEOS III is Logos Imagings lightest DR system. With a built-in battery and internal wireless commu
...
nication, the NEOS III is perfect for users that want to quickly assess an item.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window