where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1424 views
Technical Discussions
Rich Roberts
Engineering, Executive Managment
Quest Integrity Group, USA, Joined Nov 1998, 78

Rich Roberts

Engineering, Executive Managment
Quest Integrity Group,
USA,
Joined Nov 1998
78
06:57 Jan-29-2007
Panametrics - Epoc-II

We have a Panametrics - Epoc-II which has suffered some electronics damage on one of the internal circuit boards. When we contacted our local representative, we were told that Panametrics (GE) no longer support this UT scope, therefore we cannot purchase a replacement circuit board, nor could they repair it. This is such a good UT scope, we hate to give it up. Does anyone out there have the circuit schematics for the 3 or 4 boards inside this scope. If so, we can make the repairs ourselves.

An alternative would be to find another damaged Epoc-II and swap out the boards. Anyone willing to sell a damaged scope would also be a great help.

Regards, Rich



 
 Reply 
 
Joe Buckley
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 528

Joe Buckley

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
528
03:14 Jan-29-2007
Re: Panametrics - Epoc-II
Rich

Make sure you are talking to the right guy- Panametrics NDT was only briefly part of GE (They sold it when they bought Krautkramer) . Panametrics (GE sensing) is now just the Flow meter division of the old Panametrics company. The NDT Division is now part of Olympus NDT. Nothing like keeping it simple.

The EPOC II was (for its time) a pretty good scope, as you say. You may find that third party people will be able to fix it, certainly our (Sonatest) equipment of the same vintage is often easier to fix than the later equipment, since the less integrated parts then used tend to be still readily available. whereas later more specialised compenents have 'been and gone'

Good luck

Joe

----------- Start Original Message -----------
: We have a Panametrics - Epoc-II which has suffered some electronics damage on one of the internal circuit boards. When we contacted our local representative, we were told that Panametrics (GE) no longer support this UT scope, therefore we cannot purchase areplacement circuit board, nor could they repair it. This is such a good UT scope, we hate to give it up. Does anyone out there have the circuit schematics for the 3 or 4 boards inside this scope. If so, we can make the repairs ourselves.
: An alternative would be to find another damaged Epoc-II and swap out the boards. Anyone willing to sell a damaged scope would also be a great help.
: Regards, Rich
------------ End Original Message ------------




 
 Reply 
 
Simon Amallraja
Director
PET Aviation Systems P Ltd, India, Joined Jul 2003, 20

Simon Amallraja

Director
PET Aviation Systems P Ltd,
India,
Joined Jul 2003
20
08:27 Jan-30-2007
Re: Panametrics - Epoc-II
----------- Start Original Message -----------
: Rich
: Make sure you are talking to the right guy- Panametrics NDT was only briefly part of GE (They sold it when they bought Krautkramer) . Panametrics (GE sensing) is now just the Flow meter division of the old Panametrics company. The NDT Division is now part of Olympus NDT. Nothing like keeping it simple.
: The EPOC II was (for its time) a pretty good scope, as you say. You may find that third party people will be able to fix it, certainly our (Sonatest) equipment of the same vintage is often easier to fix than the later equipment, since the less integrated parts then used tend to be still readily available. whereas later more specialised compenents have 'been and gone'
: Good luck
: Joe
: : We have a Panametrics - Epoc-II which has suffered some electronics damage on one of the internal circuit boards. When we contacted our local representative, we were told that Panametrics (GE) no longer support this UT scope, therefore we cannot purchase a replacement circuit board, nor could they repair it. This is such a good UT scope, we hate to give it up. Does anyone out there have the circuit schematics for the 3 or 4 boards inside this scope. If so, we can make the repairs ourselves.
: : An alternative would be to find another damaged Epoc-II and swap out the boards. Anyone willing to sell a damaged scope would also be a great help.
: : Regards, Rich
------------ End Original Message ------------

Now they also offer buy-back scheme. EP4 series are really good. Why don't you have a look at their website.

Goodluck

Simon


 
 Reply 
 

Product Spotlight

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window