where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

765 views
Technical Discussions
Joel Norman
NDT Inspector
Canada, Joined Jun 2008, 5

Joel Norman

NDT Inspector
Canada,
Joined Jun 2008
5
06:33 Feb-25-2007
PA Gap Dimensions

Can someone explain to me exactly what the gap dimension is for a phased array probe? I haven't seen it on any probe data sheets but I have heard a few different explantions. Does it relate to the pitch?

I need to know as it is a recording requirement of ASME Sec. V, Art. 4, Appendix 4 - Examination Record (a).

Thanks,

Joel Norman


 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1303

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1303
01:00 Feb-25-2007
Re: PA Gap Dimensions
Joel:
The gap is just the space between the elements (i.e. the thickness of the saw that was used to slice the array). If you have a copy of the RD Tech "Introduction to Phased Array Ultrasonic Technology Applications" book, it is shown on page 107.
The Probe parameters such as these are essential variables so need to be itemised for a proper record of the equipment used.

Regards
Ed

----------- Start Original Message -----------
: Can someone explain to me exactly what the gap dimension is for a phased array probe? I haven't seen it on any probe data sheets but I have heard a few different explantions. Does it relate to the pitch?
: I need to know as it is a recording requirement of ASME Sec. V, Art. 4, Appendix 4 - Examination Record (a).
: Thanks,
: Joel Norman
------------ End Original Message ------------




 
 Reply 
 
Joel Norman
NDT Inspector
Canada, Joined Jun 2008, 5

Joel Norman

NDT Inspector
Canada,
Joined Jun 2008
5
03:55 Feb-26-2007
Re: PA Gap Dimensions
----------- Start Original Message -----------
: Joel:
: The gap is just the space between the elements (i.e. the thickness of the saw that was used to slice the array). If you have a copy of the RD Tech "Introduction to Phased Array Ultrasonic Technology Applications" book, it is shown on page 107.
: The Probe parameters such as these are essential variables so need to be itemised for a proper record of the equipment used.
: Regards
: Ed
:
: : Can someone explain to me exactly what the gap dimension is for a phased array probe? I haven't seen it on any probe data sheets but I have heard a few different explantions. Does it relate to the pitch?
: : I need to know as it is a recording requirement of ASME Sec. V, Art. 4, Appendix 4 - Examination Record (a).
: : Thanks,
: : Joel Norman
------------ End Original Message ------------

Thanks Ed.


 
 Reply 
 

Product Spotlight

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window