where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Sonatest Ltd
From our three distinct business centres in the UK, USA and CANADA, Sonatest design and produce a leading range of high performance ultrasonic NDT equipment and accessories.
836 views
Technical Discussions
Paolo
NDT Inspector,
Acciaierie Valbruna, Italy, Joined Nov 2006, 7

Paolo

NDT Inspector,
Acciaierie Valbruna,
Italy,
Joined Nov 2006
7
04:56 Mar-01-2007
ET testing for long products

Does anybody know ET standards for examination of steel long products (es. round bars)?
Thanks
Paolo


 
 Reply 
 
Simon Amallraja
Simon Amallraja
09:19 Mar-06-2007
Re: ET testing for long products
----------- Start Original Message -----------
: Does anybody know ET standards for examination of steel long products (es. round bars)?
: Thanks
: Paolo
------------ End Original Message ------------

Contact Mr. Phil Herman Jr @ www.phtool.com and you will get the answer.

Simon


 
 Reply 
 
Debdutta Mallik
Consultant,
Malaysia, Joined Jun 2005, 37

Debdutta Mallik

Consultant,
Malaysia,
Joined Jun 2005
37
04:22 Apr-18-2007
Eddy Current Testing for long products
Dear Paolo,
There must be a standard for acceptance criteria of for eddy current testing of your product.If it is a long product then it can be done by online system. What kind of system you have.
For eddy current generally transverse or longitudinal notches are followed for calibration.starting from 0.2 and onwards depending upon the requirement of the specification.I can provide you the information regarding online surface inspection of rails.
Dont hesitate to ask if any further information required.

Best Regards,

Debdutta Mallik


 
 Reply 
 
Frank Lund
R & D,
United Kingdom, Joined Apr 2005, 222

Frank Lund

R & D,
United Kingdom,
Joined Apr 2005
222
03:16 Apr-26-2007
Re: Eddy Current Testing for long products
Please see NEWT International's website. I'm sure we can help you.

----------- Start Original Message -----------
: Dear Paolo,
: There must be a standard for acceptance criteria of for eddy current testing of your product.If it is a long product then it can be done by online system. What kind of system you have.
: For eddy current generally transverse or longitudinal notches are followed for calibration.starting from 0.2 and onwards depending upon the requirement of the specification.I can provide you the information regarding online surface inspection of rails.
: Dont hesitate to ask if any further information required.
: Best Regards,
: Debdutta Mallik
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Research and Applications Development For NDT

The Research and Applications Development (RAD) group is a newly formed team within Acuren dedicat
...
ed to tackling challenging inspection problems. Our focus is the development of novel, field deployable, advanced inspection techniques for use in cases where standard NDT methods are ineffective. We don't wait for new innovations, we engineer them. From concept to commissioning.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

PROlineTOP Plug & Play Ultrasonic inspection device

As Plug & Play solution it units all control and operation elements in a small housing and therefo
...
re replaces the typical control cabinet...
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window