where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Materials Research Institute
Consulting to the NDT industry.
948 views
Technical Discussions
John McCanna
John McCanna
07:14 Sep-28-1999
TOFD inspection of Dry Fuel Storage Cask Closure Welds

1. I am seeking information on the application of automated TOFD to Dry Fuel (Nuclear) Storage Cask closure welds (stainless steel)?

2. Is it a suitable replacement radiography?

3. Can anyone provide a list of suppliers for this type of UT equipment as applied to the nuclear environment?


 
 Reply 
 
Jan Verkooijen
Director,
Sonovation, Netherlands, Joined Nov 1998, 29

Jan Verkooijen

Director,
Sonovation,
Netherlands,
Joined Nov 1998
29
08:24 Sep-30-1999
Re: TOFD inspection of Dry Fuel Storage Cask Closure Welds
John,

-TOFD is used quite extensively in the nuclear industry.
In fact, this is where most of the initial development
took place.
However, for this particular application,
because you say it is stainless steel, TOFD would probably
not be the best technique to use.
Because TOFD images not only anomalies (defects), but is
also sensitive enough to pick up grain boundaries, it is
usually difficult to discriminate the grain noise from
the diffraction signals at the extremities of flaws.
TOFD's role when it concerns stainless steel is therefore
mostly restricted to sizing, after detection with L-wave
Pulse-Echo probes, sometimes in combination with creep
waves etc.
-TOFD is certainly a good replacement for the standard
radiography as used in day to day practice, by example
for the inspection of piping welds during fabrication,
in the (petro-) chemical industry, which would normally
be done by conventional Gamma ray, using single exposures
(straight through the weld). When it comes to replacing
radiography utilising multiple exposures over the bevels,
TOFD will have to be complemented by other techniques such
as automated pulse-echo to achieve the same probability
of detection.
-Since nearly 20 years, AEA Sonomatic supply TOFD equipment,
services and training.

Jan Verkooijen
AEA Sonomatic


: 1. I am seeking information on the application of automated TOFD to Dry Fuel (Nuclear) Storage Cask closure welds (stainless steel)?

: 2. Is it a suitable replacement radiography?

: 3. Can anyone provide a list of suppliers for this type of UT equipment as applied to the nuclear environment?




 
 Reply 
 
Marc Hoppenbrouwers, RTD
Marc Hoppenbrouwers, RTD
00:57 Oct-04-1999
Re: TOFD inspection of Dry Fuel Storage Cask Closure Welds
xplains the name Bandscan). Each probe has a specific task in a specific depth zone. Due to the narrow focussed beam it is also possible to size quite accurately the length and height of welding defects. This concept has been developed for inspection of nuclear components in the beginning of the eighties in corporation with BAM in Berlin and was later on applied in our widely-used ROTOSCAN systems.

For more information please visit our homepages at:

http:\\www.rtd.nl (Head Office in the Netherlands)
http:\\www.rtdquality.com (Canada)

Best regards,

Marc Hoppenbrouwers
RTD, Rotterdam


: John,

: -TOFD is used quite extensively in the nuclear industry.
: In fact, this is where most of the initial development
: took place.
: However, for this particular application,
: because you say it is stainless steel, TOFD would probably
: not be the best technique to use.
: Because TOFD images not only anomalies (defects), but is
: also sensitive enough to pick up grain boundaries, it is
: usually difficult to discriminate the grain noise from
: the diffraction signals at the extremities of flaws.
: TOFD's role when it concerns stainless steel is therefore
: mostly restricted to sizing, after detection with L-wave
: Pulse-Echo probes, sometimes in combination with creep
: waves etc.
: -TOFD is certainly a good replacement for the standard
: radiography as used in day to day practice, by example
: for the inspection of piping welds during fabrication,
: in the (petro-) chemical industry, which would normally
: be done by conventional Gamma ray, using single exposures
: (straight through the weld). When it comes to replacing
: radiography utilising multiple exposures over the bevels,
: TOFD will have to be complemented by other techniques such
: as automated pulse-echo to achieve the same probability
: of detection.
: -Since nearly 20 years, AEA Sonomatic supply TOFD equipment,
: services and training.
:
: Jan Verkooijen
: AEA Sonomatic

:
: : 1. I am seeking information on the application of automated TOFD to Dry Fuel (Nuclear) Storage Cask closure welds (stainless steel)?

: : 2. Is it a suitable replacement radiography?

: : 3. Can anyone provide a list of suppliers for this type of UT equipment as applied to the nuclear environment?




 
 Reply 
 
Brian Scholes
Brian Scholes
03:39 Jan-15-2000
Re: TOFD inspection of Dry Fuel Storage Cask Closure Welds
John...

As a follow up & clarification...

The Casks we are using at Pickering are carbon steel.

We are currently using 320KV/AA film on a weld profile 1 1/4" (30mm) thick.

I'm not sure if you were involved when Structural Integrity came up to do their TOFD demonstration...

Regards,

Brian Scholes ext4413

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

: 1. I am seeking information on the application of automated TOFD to Dry Fuel (Nuclear) Storage Cask closure welds (stainless steel)?

: 2. Is it a suitable replacement radiography?

: 3. Can anyone provide a list of suppliers for this type of UT equipment as applied to the nuclear environment?




 
 Reply 
 
Mariano
Mariano
05:17 Nov-06-2006
Bruno
http://somalounger.275mb.com/


 
 Reply 
 

Product Spotlight

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

Silverwing RMS PA - Phased-array corrosion mapping

Eddyfi Technologies integrated two market leading solutions, Silverwing’s RMS and M2M’s instru
...
ments to provide a high-speed, remote access ultrasonic phased-array inspection system with live total focusing method (TFM).
>

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

Lyft™: Pulsed Eddy Current Reinvented

PEC Reinvented—CUI Programs Redefined Corrosion under insulation (CUI) is possibly the greatest u
...
nresolved asset integrity problem in the industry. Current methods for measuring wall thickness with liftoff, without removing insulation, all have severe limitations. Eddyfi introduces Lyft — a reinvented, high-performance pulsed eddy current (PEC) solution. The patent- pending system features a state-of-the-art portable instrument, real- time C-scan imaging, fast data acquisition with grid-mapping and dynamic scanning modes, and flexibility with long cables. It can also scan through thick metal and insulation, as well as aluminum, stainless steel, and galvanized steel weather jackets. Who else but Eddyfi to reinvent an eddy current technique and redefine CUI programs. Got Lyft?
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window