where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1160 views
Technical Discussions
Justin Cavanagh
Justin Cavanagh
00:20 Apr-10-2007
UT of cast iron at elevated tempratures

Has anyone got any advise for thickness inspections of cast iron valve bodies at elevated temps 280 degrees for example ???


 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
07:26 Apr-10-2007
Re: UT of cast iron at elevated tempratures
What is the maximum thickness that you need to measure? Generally, the best approach for that test would be to use a high temperature dual element transducers. Cast iron is grainy and produces a lot of scatter noise, but you should be able to measure more than 50 mm/2 inches at 2 MHz with an appropriate instrument.

Some general tips on high temperature ultrasonic testing can be found in the attached application note.

----------- Start Original Message -----------
: Has anyone got any advise for thickness inspections of cast iron valve bodies at elevated temps 280 degrees for example ???
------------ End Original Message ------------




 
 Reply 
 
Justin Cavanagh
Justin Cavanagh
03:44 Apr-10-2007
Re: UT of cast iron at elevated tempratures
The casting is about 50mm I have run a 2mhz probe over it when cold and found it effective. I was thinking that would be a good way to go sounds like I am on the right track. Will just have to buy a high temp probe.
Emat probes have also been sugested for this aplication.

----------- Start Original Message -----------
: What is the maximum thickness that you need to measure? Generally, the best approach for that test would be to use a high temperature dual element transducers. Cast iron is grainy and produces a lot of scatter noise, but you should be able to measure more than 50 mm/2 inches at 2 MHz with an appropriate instrument.
: Some general tips on high temperature ultrasonic testing can be found in the attached application note.
: : Has anyone got any advise for thickness inspections of cast iron valve bodies at elevated temps 280 degrees for example ???
------------ End Original Message ------------




 
 Reply 
 
Borja Lopez
Director
Innerspec Technologies, USA, Joined Jun 2002, 36

Borja Lopez

Director
Innerspec Technologies,
USA,
Joined Jun 2002
36
04:16 Apr-11-2007
Re: UT of cast iron at elevated tempratures
----------- Start Original Message -----------
: Has anyone got any advise for thickness inspections of cast iron valve bodies at elevated temps 280 degrees for example ???
------------ End Original Message ------------

This could be a good application for EMAT. Please visit our website for additional info www.innerspec.com


 
 Reply 
 
Massimo Carminati
Massimo Carminati
03:24 Apr-12-2007
Re: UT of cast iron at elevated tempratures
As an alternative to a dual element high temperature probe (a very good one is the d797 panametrics, but the temperature is critical). I've had excellent results using a 2MHz BB single element with a Vespel delay line with a proper delay.



 
 Reply 
 

Product Spotlight

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window