where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1128 views
Technical Discussions
Justin Cavanagh
Justin Cavanagh
00:20 Apr-10-2007
UT of cast iron at elevated tempratures

Has anyone got any advise for thickness inspections of cast iron valve bodies at elevated temps 280 degrees for example ???


 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
07:26 Apr-10-2007
Re: UT of cast iron at elevated tempratures
What is the maximum thickness that you need to measure? Generally, the best approach for that test would be to use a high temperature dual element transducers. Cast iron is grainy and produces a lot of scatter noise, but you should be able to measure more than 50 mm/2 inches at 2 MHz with an appropriate instrument.

Some general tips on high temperature ultrasonic testing can be found in the attached application note.

----------- Start Original Message -----------
: Has anyone got any advise for thickness inspections of cast iron valve bodies at elevated temps 280 degrees for example ???
------------ End Original Message ------------




 
 Reply 
 
Justin Cavanagh
Justin Cavanagh
03:44 Apr-10-2007
Re: UT of cast iron at elevated tempratures
The casting is about 50mm I have run a 2mhz probe over it when cold and found it effective. I was thinking that would be a good way to go sounds like I am on the right track. Will just have to buy a high temp probe.
Emat probes have also been sugested for this aplication.

----------- Start Original Message -----------
: What is the maximum thickness that you need to measure? Generally, the best approach for that test would be to use a high temperature dual element transducers. Cast iron is grainy and produces a lot of scatter noise, but you should be able to measure more than 50 mm/2 inches at 2 MHz with an appropriate instrument.
: Some general tips on high temperature ultrasonic testing can be found in the attached application note.
: : Has anyone got any advise for thickness inspections of cast iron valve bodies at elevated temps 280 degrees for example ???
------------ End Original Message ------------




 
 Reply 
 
Borja Lopez
Director
Innerspec Technologies, USA, Joined Jun 2002, 36

Borja Lopez

Director
Innerspec Technologies,
USA,
Joined Jun 2002
36
04:16 Apr-11-2007
Re: UT of cast iron at elevated tempratures
----------- Start Original Message -----------
: Has anyone got any advise for thickness inspections of cast iron valve bodies at elevated temps 280 degrees for example ???
------------ End Original Message ------------

This could be a good application for EMAT. Please visit our website for additional info www.innerspec.com


 
 Reply 
 
Massimo Carminati
Massimo Carminati
03:24 Apr-12-2007
Re: UT of cast iron at elevated tempratures
As an alternative to a dual element high temperature probe (a very good one is the d797 panametrics, but the temperature is critical). I've had excellent results using a 2MHz BB single element with a Vespel delay line with a proper delay.



 
 Reply 
 

Product Spotlight

Customized Probes and Transducers

With a strong development department and our own piezocomposite production, we accompany you from th
...
e first product idea to serial production. Our scientists are continuously researching new methods in the field of ultrasonic measurement technology. The progress achieved enables us to offer you optimal solutions.
>

On-Demand Webinar: Advanced Ultrasonic Techniques for HTHA Detection & Assessment

In the Oil and Gas industry, High Temperature Hydrogen Attack (HTHA) can occur in steels operating a
...
t high temperature, usually above 205°C (400°F). Early stages of HTHA are very difficult to detect. Join us for a webinar presented by Guy Maes, Zetec Sales Engineer Director. The webinar will demonstrate how advanced ultrasonic techniques are deployed for efficient and reliable HTHA inspections.
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window