where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1391 views
Technical Discussions
pankaj joshi
NDT Inspector
Indian Petrochemicals Corporation Ltd, India, Joined Jan 2005, 2

pankaj joshi

NDT Inspector
Indian Petrochemicals Corporation Ltd,
India,
Joined Jan 2005
2
09:29 May-17-2007
Ultrasonic testing at high temperature

In one of our CS column, apporx 6 inch long through and through crack is noticed. The column is in operation. We would like to carry out Ultrasonic testing in the vicinity of crack for judgement of its severity.
The operating parameters and other details of column are as under
Operating temp- 160 deg C approx
Operating pressure- around 1.0kg/cm2.
Thickness of shell- 16.0mm.

CAN ANY ONE CARRYOUT ULTRASONIC TESTING AT THIS TEMP?
CAN ANY ONE GIVE ME THE DETAILS ABOUT HIGH TEMP PROBES FOR SUCH TESTING?
IF SUCH PROBES ARE AVAILABLE IN INDIA(EX STOCK) CAN I KNOW THE ADDRESS OF THE SUPPLIER?



 
 Reply 
 
s chris
s chris
09:55 May-17-2007
Re: Ultrasonic testing at high temperature
----------- Start Original Message -----------
: In one of our CS column, apporx 6 inch long through and through crack is noticed. The column is in operation. We would like to carry out Ultrasonic testing in the vicinity of crack for judgement of its severity.
: The operating parameters and other details of column are as under
: Operating temp- 160 deg C approx
: Operating pressure- around 1.0kg/cm2.
: Thickness of shell- 16.0mm.
: CAN ANY ONE CARRYOUT ULTRASONIC TESTING AT THIS TEMP?
: CAN ANY ONE GIVE ME THE DETAILS ABOUT HIGH TEMP PROBES FOR SUCH TESTING?
: IF SUCH PROBES ARE AVAILABLE IN INDIA(EX STOCK) CAN I KNOW THE ADDRESS OF THE SUPPLIER?
------------ End Original Message ------------

KB makes shear wave shoes and probes that will operate at that temp.


 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
04:59 May-18-2007
Re: Ultrasonic testing at high temperature
We have an application note on the subject of high temperature ultrasonic testing that may be of interest... see the link below.

At 160 C, coupling will not be a big problem with any of a number of commercially available high temperature couplants. High temperature wedges are available in the Panametrics-NDT line from Olympus NDT as well as other sources. The primary issue to remember with ANY high temperature wedge -- ours or those from our competitors -- is that refracted angle will change as the wedge heats up. This is because sound velocity changes with temperature in all materials, and as the temperature of the wedge increases and its velocity decreases, the refracted angle will increase in accordance with Snell's Law. This does not usually affect your ability to detect cracks, but it creates some uncertainty in the accuracy with which you can measure distance and depth.




 
 Reply 
 
Ahmed Eid
Other, researcher
National Institute for Standards, Egypt, Joined Oct 1999, 1

Ahmed Eid

Other, researcher
National Institute for Standards,
Egypt,
Joined Oct 1999
1
09:11 May-19-2007
Re: Ultrasonic testing at high temperature
You may use a delay technique.

Ahmed Eid

----------- Start Original Message -----------
: In one of our CS column, apporx 6 inch long through and through crack is noticed. The column is in operation. We would like to carry out Ultrasonic testing in the vicinity of crack for judgement of its severity.
: The operating parameters and other details of column are as under
: Operating temp- 160 deg C approx
: Operating pressure- around 1.0kg/cm2.
: Thickness of shell- 16.0mm.
: CAN ANY ONE CARRYOUT ULTRASONIC TESTING AT THIS TEMP?
: CAN ANY ONE GIVE ME THE DETAILS ABOUT HIGH TEMP PROBES FOR SUCH TESTING?
: IF SUCH PROBES ARE AVAILABLE IN INDIA(EX STOCK) CAN I KNOW THE ADDRESS OF THE SUPPLIER?
------------ End Original Message ------------




 
 Reply 
 
Gath Cheyne
Gath Cheyne
03:41 May-27-2007
Re: Ultrasonic testing at high temperature
----------- Start Original Message -----------
: In one of our CS column, apporx 6 inch long through and through crack is noticed. The column is in operation. We would like to carry out Ultrasonic testing in the vicinity of crack for judgement of its severity.
: The operating parameters and other details of column are as under
: Operating temp- 160 deg C approx
: Operating pressure- around 1.0kg/cm2.
: Thickness of shell- 16.0mm.
: CAN ANY ONE CARRYOUT ULTRASONIC TESTING AT THIS TEMP?
: CAN ANY ONE GIVE ME THE DETAILS ABOUT HIGH TEMP PROBES FOR SUCH TESTING?
: IF SUCH PROBES ARE AVAILABLE IN INDIA(EX STOCK) CAN I KNOW THE ADDRESS OF THE SUPPLIER?
------------ End Original Message ------------

If the material that is to be inspected is metalic, EMAT can be used; this method is capable of operating at temperatures of 1000 deg C. Contact: Innerspec Technologies.




 
 Reply 
 
Simon Amallraja
Simon Amallraja
08:18 May-28-2007
Re: Ultrasonic testing at high temperature
----------- Start Original Message -----------
: In one of our CS column, apporx 6 inch long through and through crack is noticed. The column is in operation. We would like to carry out Ultrasonic testing in the vicinity of crack for judgement of its severity.
: The operating parameters and other details of column are as under
: Operating temp- 160 deg C approx
: Operating pressure- around 1.0kg/cm2.
: Thickness of shell- 16.0mm.
: CAN ANY ONE CARRYOUT ULTRASONIC TESTING AT THIS TEMP?
: CAN ANY ONE GIVE ME THE DETAILS ABOUT HIGH TEMP PROBES FOR SUCH TESTING?
: IF SUCH PROBES ARE AVAILABLE IN INDIA(EX STOCK) CAN I KNOW THE ADDRESS OF THE SUPPLIER?
------------ End Original Message ------------

This problem can be addressed by regular UT Equipment with suitable probe. Contact us for furtehr details. We at Mahindra Intertrade, will give you complete solutions for your application.

D.Simon Amallraja.


 
 Reply 
 

Product Spotlight

GUL Subsea Solutions - Screeening & Monitoring

To inspect new and existing subsea lines, you need proven technology and experience. GUL offers it's
...
technology to solve this challenge: GUL Subsea and gMAT Transducer Rings.
>

VeeScan AirCraft Wheel Inspection

The VEESCAN offers maximum flexibility, has a proven mechanical design and records of breakdown-fr
...
ee operation of over 365 days. Appealing to companies in the Aerospace industry, the VEESCAN is ideal for all wheel-testing environments. With a wide selection of probes, the VeeScan allows your wheel testing facility the flexibility to select the most compatible configurations with their workload.
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window