where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Acoustic Emission Consulting, Inc.
Acoustic Emission Consulting, Inc. specializes in the design of small portable AE instruments for field and lab use.
2308 views
Technical Discussions
Binh, Du Xuan
Binh, Du Xuan
02:24 Aug-24-2007
NDT after PWHT

Dear All,

Pipe spool fabrication base on Code and standards B31.3.

Everyone can give to me advice ?

MT after PWHT shall be done or not necessary ?

Thanks and Best Regards,


 
 Reply 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
08:38 Aug-24-2007
Re: NDT after PWHT

See B31.3 Para. 341.3.1.(a) "For P-Nos. 3, 4, and 5 materials, examination shall be performed after completion of any heat treatment."

This implies that P1 and P2 materials do not require examination after heat treatment UNLESS otherwise specified by the contract or relevant procedures.


 
 Reply 
 
G.Madhesan
G.Madhesan
08:29 Aug-24-2007
Re: NDT after PWHT
MT must be carriedout after any PWHT for detectingany stress cracks.
Regards,
Madhesan





 
 Reply 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
04:53 Aug-25-2007
Re: NDT after PWHT
Madhesan

Yes you are right MT, is for detecting cracks (amongst other defects), however the Code writers are very experienced in the welding and heat-treating of standard materials (i.e. Group P1) and are sufficiently confident that proper PWHT of such materials will not cause cracking to be able to codify this with no requirement for PWHT MT. So in the case of welding plain carbon (P1)steels, "must" does not apply.


----------- Start Original Message -----------
: MT must be carriedout after any PWHT for detectingany stress cracks.
: Regards,
: Madhesan
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Navic - Steerable Modular Automated Scanner

The Navic is a modular, motorized, steerable scanner designed to carry multiple attachments used
...
in various scanning and inspection applications. The Navic is capable of weld scanning (girth welds and long seam welds), automated corrosion mapping, and tank scanning.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window