where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Hi-Spec Systems
we are specialised in the design, development and manufacture of Phased Array and Time-of-Flight Diffraction (ToFD) ultrasonic inspection systems.
2212 views
Technical Discussions
Binh, Du Xuan
Binh, Du Xuan
02:24 Aug-24-2007
NDT after PWHT

Dear All,

Pipe spool fabrication base on Code and standards B31.3.

Everyone can give to me advice ?

MT after PWHT shall be done or not necessary ?

Thanks and Best Regards,


    
 
 Reply 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
08:38 Aug-24-2007
Re: NDT after PWHT

See B31.3 Para. 341.3.1.(a) "For P-Nos. 3, 4, and 5 materials, examination shall be performed after completion of any heat treatment."

This implies that P1 and P2 materials do not require examination after heat treatment UNLESS otherwise specified by the contract or relevant procedures.


    
 
 Reply 
 
G.Madhesan
G.Madhesan
08:29 Aug-24-2007
Re: NDT after PWHT
MT must be carriedout after any PWHT for detectingany stress cracks.
Regards,
Madhesan





    
 
 Reply 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
04:53 Aug-25-2007
Re: NDT after PWHT
Madhesan

Yes you are right MT, is for detecting cracks (amongst other defects), however the Code writers are very experienced in the welding and heat-treating of standard materials (i.e. Group P1) and are sufficiently confident that proper PWHT of such materials will not cause cracking to be able to codify this with no requirement for PWHT MT. So in the case of welding plain carbon (P1)steels, "must" does not apply.


----------- Start Original Message -----------
: MT must be carriedout after any PWHT for detectingany stress cracks.
: Regards,
: Madhesan
------------ End Original Message ------------




    
 
 Reply 
 

Product Spotlight

NOVO Armor 15 & NOVO Armor 22

The Armor Kit Contains the NOVO Armor, which provides additional mechanical protection to the NOVO 1
...
5WN & NOVO 22WN Detectors, the Armor Stand and a traveling soft cover. - Newest shock absorbent technology case - Water resistant design - Supports wired & wireless communication - Multiple positioning options - Tripod connection using the Built-in 1/4” threads - Simple Detector battery replacement
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

TOPAZ® 64: Fully Integrated Portable 32 or 64 Channel PAUT Instrument with FMC & TFM

Introducing TOPAZ64, the industry’s most intelligent fully integrated, portable 32 or 64-channel
...
phased array ultrasound (UT) instrument. TOPAZ64 combines code-compliant phased array UT with the industry’s most advanced full matrix capture (FMC) and total focusing method (TFM) capabilities. Featuring the highest acquisition frequency in its class, high resolution FMC and a 12” multi-touchscreen, users can easily visualize even the smallest flaws. TOPAZ64 can generate a bipolar pulse that provides more acoustic energy versus previous models for punching through thick components. The result is a portable tool that delivers increased inspection coverage, more accurate signals, and the ability to handle all UT inspections in one package. TOPAZ64 is ideal for challenging applications in transportation, oil and gas, manufacturing and power generation.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window