where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

7578 views
Technical Discussions
Azrul Hilmi
Azrul Hilmi
03:25 Sep-12-2007
B31 code case 179

Dear All,

Just wondering, do you know where can I get a copy of the B31 code case 179 'Use of Alternative Ultrasonic Examination in Lieu of Radiography for B31.1 Applications in Materials ½ inch and Less in Wall Thickness'. I've checked with IHS, and they do not have it.

rgds
Azrul


 
 Reply 
 
John O'Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 281

John O'Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
281
04:07 Sep-12-2007
Re: B31 code case 179
Its actually Code Case 181

the following link should get you to it.


cstools.asme.org/csconnect/pdf/CommitteeFiles/15243.pdf



 
 Reply 
 
Azrul Hilmi
Azrul Hilmi
06:53 Sep-12-2007
Re: B31 code case 179
I can confirm it is definitely Code Case 179.
Anybody know where I can get it?

----------- Start Original Message -----------
: Its actually Code Case 181
: the following link should get you to it.
:
: cstools.asme.org/csconnect/pdf/CommitteeFiles/15243.pdf
------------ End Original Message ------------




 
 Reply 
 
David Mackintosh
Engineering,
Acuren Group Inc., Canada, Joined Feb 2011, 85

David Mackintosh

Engineering,
Acuren Group Inc.,
Canada,
Joined Feb 2011
85
08:03 Sep-17-2007
Re: B31 code case 179
B31 Case 179 (for B31.1) — "Use of Ultrasonic Examination in Lieu of Radiography for B31.1 Applications in Materials 1⁄2 in. and Less in Wall Thickness" is published in ASME B31.1b-2006, Addenda to ASME B31.1-2004, Power Piping, page C-22. (B31.1 itself only allows UT on wall thicknesses greater than ½ inch.)

B31 Case 181 (for B31.3) — "Use of Alternative Ultrasonic Examination Acceptance Criteria in ASME B31.3" describes conditions for fracture mechanics evaluation of flaws. Almost identical to Code Case 2235, except that there is no lower limit on wall thickness.
Available at http://cstools.asme.org/csconnect/pdf/CommitteeFiles/15243.pdf


----------- Start Original Message -----------
: Dear All,
: Just wondering, do you know where can I get a copy of the B31 code case 179 'Use of Alternative Ultrasonic Examination in Lieu of Radiography for B31.1 Applications in Materials ½ inch and Less in Wall Thickness'. I've checked with IHS, and they do not have it.
: rgds
: Azrul
------------ End Original Message ------------




 
 Reply 
 
Owen Konski
Owen Konski
01:44 Jul-15-2008
Re: B31 code case 179
The link provided takes you to what is for B31.3 (Case 181) and a couple other Cases however the 179 is not in the document. Are you saying Case 181 applies in lieu of 179?


----------- Start Original Message -----------
: Its actually Code Case 181
: the following link should get you to it.
:
: cstools.asme.org/csconnect/pdf/CommitteeFiles/15243.pdf
------------ End Original Message ------------




 
 Reply 
 
Wilyan Safitra
NDT Inspector,
Indonesia, Joined Sep 2010, 16

Wilyan Safitra

NDT Inspector,
Indonesia,
Joined Sep 2010
16
06:59 May-11-2015
Re: B31 code case 179
Download

Download

Download

B31 code case 179 2006 edition
 
 Reply 
 
Bill
USA, Joined Jan 2010, 52

Bill

USA,
Joined Jan 2010
52
22:45 May-11-2015
Re: B31 code case 179
In Reply to David Mackintosh at 08:03 Sep-17-2007 .

David,

FYI-Both of the references you made are very out dated.

 
 Reply 
 

Product Spotlight

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

Echomac® PA Tube Weld Tester

The new robotic Echomac® PA TW is an operator friendly test system for detecting weld zone defects
...
in tube and pipe caused by scarfing or welding processes. Electronic scanning ensures that the entire weld zone is covered without the need for mechanical movement or operator adjustment.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window