where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Modsonic Instruments Mfg Co Pvt Ltd
We are leading Indian manufacturer and exporter of portable “Ultrasonic Testing Equipment”
3716 views
Technical Discussions
Sandy Coldwell
Sandy Coldwell
06:35 Sep-28-1999
Aluminum Casting NDT Suggestions

I am a student in the United States and new to non-destructive testing techniques. Can you suggest available (or easily modifiable) methods to test C355 aluminum cast parts - specifically turbocharger compressor wheels. The method should be relatively inexpensive, reliable, and easily interpretable.

Thanks
Sandy Coldwell
(a starving Mechanical Engineering student)
ws.coldwell@prodigy.net


 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
09:34 Sep-28-1999
Re: Aluminum Casting NDT Suggestions

: I am a student in the United States and new to non-destructive testing techniques. Can you suggest available (or easily modifiable) methods to test C355 aluminum cast parts - specifically turbocharger compressor wheels. The method should be relatively inexpensive, reliable, and easily interpretable.

Are you looking to perform thickness gaging, flaw detection, or material properties analysis? It is possible that common ultrasonic NDT techniques using off-the-shelf equipment could be employed for all three, but I'd need more information on exactly what you're trying to do to say more. If it's thickness gaging, we would need to know the thickness range, resolution/accuracy requirements, and whether there were any geometrical limitations like non-parallel walls or restricted access for probes. For flaw detection, we'd need to know the EXACT part geometry as well as the type, location, minimum size, and geometry of the anomalies that you're looking for. For material properties, ultrasonic techniques can often be used to quantify elastic modulus, as well as for analyzing grain size and distribution and a few other less common tests.

Based on a further definition of your test requirements, possibly followed by evaluation of representative samples of the parts in question, ultrasonic equipment from companies like mine may meet your needs.

--Tom Nelligan



 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 305

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
305
08:09 Sep-29-1999
Re: Aluminum Casting NDT Suggestions
: I am a student in the United States and new to non-destructive testing techniques. Can you suggest available (or easily modifiable) methods to test C355 aluminum cast parts - specifically turbocharger compressor wheels. The method should be relatively inexpensive, reliable, and easily interpretable.

: Thanks
: Sandy Coldwell
: (a starving Mechanical Engineering student)

Our company is using Resonant Inspection in inspecting many different component types for customers.
This is mainly used in testing mass produced components, especially for the automotive industry.

I have looked at cast Turbocharger Compressors for another customer, and have concluded that we could probably test these parts also, but the tests would probably have to be carried out before the balancing process of manufacturing.
We expect to detect cracks and also internal porosity, provided that the defects are sufficiently serious enough to have ANY effect on the structural integrity of the part.
If the defects do not have an effect on this, then we do not detect them (and you probably dont want to reject these parts).

The test would (after setting it up) provide a Go-NoGo signal for acceptance and rejection. Testing times typically of 3 to 6 seconds per piece are normal, and when looking at mass produced parts, payback of the systems are usually realised within 12 to 18 months, sometimes less.

Let me have some details, and I will get our USA contact to get in touch.

Regards,

Godfrey Hands





 
 Reply 
 
Mark Davis
Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama, USA, Joined Mar 2000, 85

Mark Davis

Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama,
USA,
Joined Mar 2000
85
00:33 Dec-02-1999
Re: Aluminum Casting NDT Suggestions
One method is digital radiography. I am with the University of Alabama in Birmingham. We are performing UT and Radiography on casting and then eveluating digital radiography for feature characterization.

You may call me at (205) 714-3701.

Sincerely,

J. Mark Davis




 
 Reply 
 
Eng. Fathi Ghanameh
Eng. Fathi Ghanameh
02:25 Dec-23-1999
Re: Aluminum Casting NDT Suggestions
: I am a student in the United States and new to non-destructive testing techniques. Can you suggest available (or easily modifiable) methods to test C355 aluminum cast parts - specifically turbocharger compressor wheels. The method should be relatively inexpensive, reliable, and easily interpretable.

: Thanks
: Sandy Coldwell
: (a starving Mechanical Engineering student)
: ws.coldwell@prodigy.net




 
 Reply 
 
jason scott
jason scott
00:11 Mar-27-2000
Re: Aluminum Casting NDT Suggestions
penetrant tests will give you quite accurate results for surface breaking flaws, this can be very portable or usuually involves the use of fluorescent inspection within the aerospace industry, this method isn't as portable but very effective

radiography is also used on this kind of part and also effective especially for volumetric type flaws, this would generally be quite expensive though depending on local resources

if i can be of any furthe assistance contact me on the above e-mail address


 
 Reply 
 
behrooz movahedi
behrooz movahedi
08:27 Mar-02-2002
Re: Aluminum Casting NDT Suggestions
: I am a student in the isfahan university of technology and new to non-destructive testing techniques. Can you suggest available (or easily modifiable) methods to test C355 aluminum cast parts - specifically turbocharger compressor wheels. The method should be relatively inexpensive, reliable, and easily interpretable.

: Thanks
: behrooz movahedi
: DEBT.MATERIALS ENG.



 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window