where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

604 views
Technical Discussions
Doug Mendes
NDT Inspector, R & D
Imetrix Inc., USA, Joined Oct 1999, 7

Doug Mendes

NDT Inspector, R & D
Imetrix Inc.,
USA,
Joined Oct 1999
7
09:18 Dec-08-1999
Double hulled structures

I'm interested in using ultrasonics to inspect a structure that has two steel plates which have a water path between the two plates. I need to inspect one of the plates for corrosion and pitting through the water column and the other plate. I only have access to one side of this structure which complicated matters. The plates are less than 1/2'' (12.7mm) thick but the water path is unknown. My question is could this inspection be performed and what if any special equipment would be needed? The water path would be known before the inspection. Any help would be grreatly appreciated.


 
 Reply 
 
M. William Moyer
M. William Moyer
02:17 Dec-08-1999
Re: Double hulled structures
Another approach is to use a pitch catch setup, particularly if you are inspecting in immersion. Set up the transducers for 45 deg
shear in the steel. The spacing should be such that you can geometrically focus the transducer array at about 3-4 inches (for 0.5 inch steel).
Move the transducer pair toward the part until they are geometrically focused on the back surface of the first hull. This signal will peak up. Then
continue to move in until you are focused on the surface of interest. Because of the angles, the multiple reflections will be very small and only the
signal of interest will be seen. This technique works well on many multilayer inspections.
The technique is described in "Ultrasonic Inspection Using the Pitch-Catch Technique," M. W. Moyer,Materials Evaluation, Vol 37, Number 5, April, 1979,
pg. 51.

M. William Moyer
ult@y12.doe.gov.

:
: : I'm interested in using ultrasonics to inspect a structure that has two steel plates which have a water path between the two plates. I need to inspect one of the plates for corrosion and pitting through the water column and the other plate. I only have access to one side of this structure which complicated matters. The plates are less than 1/2'' (12.7mm) thick but the water path is unknown. My question is could this inspection be performed and what if any special equipment would be needed? The water path would be known before the inspection. Any help would be grreatly appreciated.

: This is an application that we've run into on several previous occasions, with mixed results. The biggest complication is that multiple echoes from the outer plate and the water gap will be superimposed over the echoes from the near and far wall of the inner plate. Whether this will be a major problem or just an annoyance will depend on the exact thickness of the outer plate and the exact length of the water path and thus the spacing of the echoes. If you're lucky, the echoes from the inner plate will occur between, rather than on top of, other signals. (But Murphy's Law usually insures that everything will be superimposed!)

: In that case, you might investigate the possibility of using digital signal processing to subtract the outer plate and water path echoes from the wave train. Unfortunately, that too gets complicated if the outer plate thickness and water gap length are varying from point to point, since that will change the wave pattern that you need to subtract.

: --Tom Nelligan




 
 Reply 
 

Product Spotlight

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

AIS229 - Multipurpose Real Time System

Latest standard & automatic real time system developed by Balteau. The AIS229 has been designed to
...
do series inspection in a wide variety of industry. Composed of a shielded cabinet, 5 axis manipulator, x-ray generator and tubehead from 160kV to 225kV, a fl at panel & much more, the AIS229 is most certainly one of the most multipurpose RTR system available on the market.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Echomac® PA Tube Weld Tester

The new robotic Echomac® PA TW is an operator friendly test system for detecting weld zone defects
...
in tube and pipe caused by scarfing or welding processes. Electronic scanning ensures that the entire weld zone is covered without the need for mechanical movement or operator adjustment.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window