where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Iris Inspection Services, Inc.
We are the world's largest supplier of air cooler, boiler and exchanger tubing inspection services.
455 views
Technical Discussions
Yasin Karavacýoðlu
Yasin Karavacýoðlu
03:37 Dec-13-1999
lamb wave prob

Anybody know that where can ý obtain lamb waves probes?
My detectors are Krautkramer USN 52, Krautkramer USD 15


 
 Reply 
 
Paul A. Meyer
R & D,
GE Inspection Technologies, USA, Joined Nov 1998, 47

Paul A. Meyer

R & D,
GE Inspection Technologies,
USA,
Joined Nov 1998
47
04:41 Dec-13-1999
Re: lamb wave prob
Hi Yasin,
Lamb Waves are generated when you impinge the surface of your part with a conventional wave (typically longitudinal) at the appropriate angle to generate the desired Lamb mode in your part. Therefore, conventional angle beam probes can be used if you select the correct angle and frequency. This selection involves understanding the testpiece geometry and the many possible Lamb modes that can be generated in it. Then you can select the necessary test configuration (probes, frequency, etc.).
It is also possible to use variable angle probes having broad bandwidth so that many modes can be generated by changing angle and frequency content.
More recently, phased array probes are being used to select modes electronically.
But, once again, your first step is stating your test piece and flaw geometries.
Regards,
Paul

: Anybody know that where can ý obtain lamb waves probes?
: My detectors are Krautkramer USN 52, Krautkramer USD 15




 
 Reply 
 

Product Spotlight

ISONIC 3510

Very Powerful Superior Performance Extremely Portable Smart Phased Array Ultrasonic Flaw Detector an
...
d Recorder with 2 Conventional UT and TOFD Channels uniquely combines PA, single- and multi-channel conventional UT, and TOFD modalities providing 100% raw data recording and imaging. Suitable for all kinds of every-day ultrasonic inspections
>

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window