where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

3019 views
Technical Discussions
lamb waves
lamb waves
09:11 Dec-14-2007
how to Exciting lamb waves ?

hi

i am trying to simulate Lamb waves on Ansys or ABAQUS.

but i am confused by Excitation of Lamb waves(A0 / S0 mode).

someone says that applying a harmonic normal force to small regions of the top and bottom surfaces of your model could be a simple way.

i also get another way from one article ,which apply a shear force on the surface of model.

as we know, if i wana Excitate lamb waves , shouldn't i put the incident wave and the plane surface with a particular angle, rather than vertical or horizontal orientation ?

somebody helps me please.




 
 Reply 
 
Michael Moles †2014 *1948
, Joined ,
04:17 Dec-14-2007
Re: how to Exciting lamb waves ?
----------- Start Original Message -----------
: hi
: i am trying to simulate Lamb waves on Ansys or ABAQUS.
: but i am confused by Excitation of Lamb waves(A0 / S0 mode).
: someone says that applying a harmonic normal force to small regions of the top and bottom surfaces of your model could be a simple way.
: i also get another way from one article ,which apply a shear force on the surface of model.
: as we know, if i wana Excitate lamb waves , shouldn't i put the incident wave and the plane surface with a particular angle, rather than vertical or horizontal orientation ?
: somebody helps me please.
------------ End Original Message ------------

May I suggest contacting Prof. Joseph Rose at Penn State or Peter Cawley at Imperial College, London.

Michael


 
 Reply 
 
Thomas Vogt
R & D, - -
Guided Ultrasonics Ltd, United Kingdom, Joined Apr 2007, 22

Thomas Vogt

R & D, - -
Guided Ultrasonics Ltd,
United Kingdom,
Joined Apr 2007
22
09:02 Dec-14-2007
Re: how to Exciting lamb waves ?
Basically both ways are valid to excite a certain guided wave mode, it just requires different ways of thinking about it.

For modelling, what you do is to match the excitation to the mode shape (stress and displacement fields). Experimentally, to excite a certain mode you can do the same (for example to excite A0 in a plate you could place two shear PZT-elements on either side of the plate and drive them out of phase, to excite S0 you would do the same but drive them in phase).

The other way is to send in a plane wave at a certain angle - this way you make sure that the excited guided wave has a certain wavelength. Together with the frequency this fixes one point in the dispersion plot - if the dispersion curve of your desired mode runs through this point it will be excited.

Hope this helps,
Tom

----------- Start Original Message -----------
: hi
: i am trying to simulate Lamb waves on Ansys or ABAQUS.
: but i am confused by Excitation of Lamb waves(A0 / S0 mode).
: someone saysthat applying a harmonic normal force to small regions of the top and bottom surfaces of your model could be a simple way.
: i also get another way from one article ,which apply a shear force on the surface of model.
: as we know, if i wana Excitate lamb waves , shouldn't i put the incident wave and the plane surface with a particular angle, rather than vertical or horizontal orientation ?
: somebody helps me please.
------------ End Original Message ------------




 
 Reply 
 
lamb waves
lamb waves
06:19 Dec-16-2007
Re: how to Exciting lamb waves ?
Thanks tom!
that helps me a lot!

but i'm still curious about driving pzt-elements out of phase or in phase.

if i wanna use direct force or displacement instead of pzt-elements, how to apply my loads?

for A0, apply the same harmonic normal forces ,which start towards the same directions, to small regions of the top and bottom surfaces.

for S0, apply the same harmonic normal forces ,which start towards the opposite directions, to small regions of the top and bottom surfaces.

for A0+S0, apply the same harmonic normal forces only to the top surfaces.

am i right?

sorry for my poor english.

waiting for your reply.

Charles

----------- Start Original Message -----------
: Basically both ways are valid to excite a certain guided wave mode, it just requires different ways of thinking about it.
: For modelling, what you do is to match the excitation to the mode shape (stress and displacement fields). Experimentally, to excite a certain mode you can do the same (for example to excite A0 in a plate you could place two shear PZT-elements on either side of the plate and drive them out of phase, to excite S0 you would do the same but drive them in phase).
: The other way is to send in a plane wave at a certain angle - this way you make sure that the excited guided wave has a certain wavelength. Together with the frequency this fixes one point in the dispersion plot - if the dispersion curve of your desired mode runs through this point it will be excited.
: Hope this helps,
: Tom
: : hi
: : i am trying to simulate Lamb waves on Ansys or ABAQUS.
: : but i am confused by Excitation of Lamb waves(A0 / S0 mode).
: : someone says that applying a harmonic normal force to small regions of the top and bottom surfaces of your model could be a simple way.
: : i also get another way from one article ,which apply a shear force on the surface of model.
: : as we know, if i wana Excitate lamb waves , shouldn't i put the incident wave and the plane surface with a particular angle, rather than vertical or horizontal orientation ?
: : somebody helps me please.
------------ End Original Message ------------




 
 Reply 
 
Sang Kim
Consultant, NDT Trainer
Guided Wave Analysis LLC, USA, Joined Feb 2008, 44

Sang Kim

Consultant, NDT Trainer
Guided Wave Analysis LLC,
USA,
Joined Feb 2008
44
00:11 Dec-18-2007
Re: how to Exciting lamb waves ?
Another way to generate guided waves in plate directly excites the particle displacement in the material. Magnetostrictive sensor (MsS) technology is used to generate symmetric Lamb(S0), asymmetric Lamb(A0), and shear-horizontal (SH0). The S0- and AO-mode waves have out-of-plane and in-plane (parallel to wave propagation direction) particle motion. The SH0-wave has in-plane (perpendicular to the wave propagation direction) particle motion. In order to check how strongly these guided waves are generated with MsS probe, please refer to http://www.gwanalysis.com/plate_structure.html for shear-horizontal wave and to http://www.gwanalysis.com/matrix_breaking.html for S0 Lamb wave.

I hope it help you.

Sang

----------- Start Original Message -----------
: Thanks tom!
: that helps me a lot!
: but i'm still curious about driving pzt-elements out of phase or in phase.
: if i wanna use direct force or displacement instead of pzt-elements, how to apply my loads?
: for A0, apply the same harmonic normal forces ,which start towards the same directions, to small regions of the top and bottom surfaces.
: for S0, apply the same harmonic normal forces ,which start towards the opposite directions, to small regions of the top and bottom surfaces.
: for A0+S0, apply the same harmonic normal forces only to the top surfaces.
: am i right?
: sorry for my poor english.
: waiting for your reply.
: Charles
: : Basically both ways are valid to excite a certain guided wave mode, it just requires different ways of thinking about it.
: : For modelling, what you do is to match the excitation to the mode shape (stress and displacement fields). Experimentally, to excite a certain mode you can do the same (for example to excite A0 in a plate you could place two shear PZT-elements on either side of the plate and drive them out of phase, to excite S0 you would do the same but drive them in phase).
: : The other way is to send in a plane wave at a certain angle - this way you make sure thatthe excited guided wave has a certain wavelength. Together with the frequency this fixes one point in the dispersion plot - if the dispersion curve of your desired mode runs through this point it will be excited.
: : Hope this helps,
: : Tom
: : : hi
: : : i am trying to simulate Lamb waves on Ansys or ABAQUS.
: : : but i am confused by Excitation of Lamb waves(A0 / S0 mode).
: : : someone says that applying a harmonic normal force to small regions of the top and bottom surfaces of your model could be a simple way.
: : : i also get another way from one article ,which apply a shear force on the surface of model.
: : : as we know, if i wana Excitate lamb waves , shouldn't i put the incident wave and the plane surface with a particular angle, rather than vertical or horizontal orientation ?
: : : somebody helps me please.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

OPBOX with standard software is able to do all types of inspections and measurements: flaw detection in welds and materials, scanning of objects, testing composite materials, forged and moulded pieces, many UT inspections, measurements of properties of ma

Typical applications: UT measurements with pulse technique, Measurement of thicknesses also at hig
...
h temperatures, Measurements of properties of materials, including fluids and gases We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
>

YXLON Cougar EVO

Scalable small footprint X-ray inspection systems for assembly and laboratory applications. The
...
YXLON Cougar EVO series was designed to provide the "best-in- class" inspection solutions for SMT, semiconductor, and laboratory assembly applications, while maintaining a small system footprint for maximum convenience. With optimized software and hardware, these systems produce higher quality and more consistent results than other electronics inspection systems currently on the market.
>

NOVO Armor 15 & NOVO Armor 22

The Armor Kit Contains the NOVO Armor, which provides additional mechanical protection to the NOVO 1
...
5WN & NOVO 22WN Detectors, the Armor Stand and a traveling soft cover. - Newest shock absorbent technology case - Water resistant design - Supports wired & wireless communication - Multiple positioning options - Tripod connection using the Built-in 1/4” threads - Simple Detector battery replacement
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window