where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

919 views
Technical Discussions
steve
NDT Inspector,
Bureau Veritas Asset Integrity & Reliability Services, Australia, Joined Aug 2005, 6

steve

NDT Inspector,
Bureau Veritas Asset Integrity & Reliability Services,
Australia,
Joined Aug 2005
6
00:55 Dec-27-2007
NDT Capability

Wow...It is a scary world!

It is my perception that there is a rising frequency of posts to this forum from inexperienced technicians, particular in the fields of ultrasonics and radiography, asking questions that should be addressed by training, in-house procedures and Level III supervisors.

This Technical Discussions Forum is a great tool for seeking peer review, or advice, from NDT practitioners that are faced with a task that is outside of their normal scope of testing.

It is also a great forum to discuss the merits or failings of codes, standards or inspection technologies.

It should not be seen as a replacement or stop-gap for training.

Please don't misunderstand me, I am not critical of the persons posting the messages, in fact I applaud them for seeking the advice of their worthy peers that take the time to attempt to assist them where they can.

However, I do wonder why they use this forum for this purpose. Is it because they don't have, or have access to, training, in-house procedures and Level III supervisors?

If this is the case, our industry is in trouble.


 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
03:30 Dec-31-2007
Re: NDT Capability
Steve,

You are right. While we should certainly applaud and appreciate their inerest in learning, the situation does point to an alarming situation where they are required to fend for thenselves without any help inhouse. Cost cutting measures, appear smart in the short run but can be catastrophic.

Let us help them as much as we can, keeping the safety aspects in view.

Swamy


----------- Start Original Message -----------
: Wow...It is a scary world!
: It is my perception that there is a rising frequency of posts to this forum from inexperienced technicians, particular in the fields of ultrasonics and radiography, asking questions that should be addressed by training, in-house procedures and Level III supervisors.
: This Technical Discussions Forum is a great tool for seeking peer review, or advice, from NDT practitioners that are faced with a task that is outside of their normal scope of testing.
: It is also a great forum to discuss the merits or failings of codes, standards or inspection technologies.
: It should not be seen as a replacement or stop-gap for training.
: Please don't misunderstand me, I am not critical of the persons posting the messages, in fact I applaud them for seeking the advice of their worthy peers that take the time to attempt to assist them where they can.
: However, I do wonder why they use this forum for this purpose. Is it because they don't have, or have access to, training, in-house procedures and Level III supervisors?
: If this is the case, our industry is in trouble.
------------ End Original Message ------------




 
 Reply 
 
Michel
NDT Inspector,
consultant, Canada, Joined Sep 2006, 897

Michel

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
897
07:31 Jan-03-2008
Re: NDT Capability
Hi Guys,

I've been in the NDT business since 1989 and got my training from the Canadian Air Force. I retired in 1996 and was able to gain experience in various industries, yet I don't know it all.

With our profession changing so fast, no amount of training and supervision will teach you everything. This forum is in my opinion a place where we as technician can come and learn about a situation we might have not encounter before. In the past, I've worked with helpers that were very knowledgeable in their industry and also with Level 3 that were unfamiliar with my industry.

I guess what I'm trying to say is that we should keep an open mind. Helping and teaching one another will only reflect positively on our profession.

----------- Start Original Message -----------
: Steve,
: You are right. While we should certainly applaud and appreciate their inerest in learning, the situation does point to an alarming situation where they are required to fend for thenselves without any help inhouse. Cost cutting measures, appear smart in the short run but can be catastrophic.
: Let us help them as much as we can, keeping the safety aspects in view.
: Swamy
:
: : Wow...It is a scary world!
: : It is my perception that there is a rising frequency of posts to this forum from inexperienced technicians, particular in the fields of ultrasonics and radiography, asking questions that should be addressed by training, in-house procedures and Level III supervisors.
: : This Technical Discussions Forum is a great tool for seeking peer review, or advice, from NDT practitioners that are faced with a task that is outside of their normal scope of testing.
: : It is also a great forum to discuss the merits or failings of codes, standards or inspection technologies.
: : It should not be seen as a replacement or stop-gap for training.
: : Please don't misunderstand me, I am not critical of the persons posting the messages, in fact I applaud them for seeking the advice of their worthy peers that takethe time to attempt to assist them where they can.
: : However, I do wonder why they use this forum for this purpose. Is it because they don't have, or have access to, training, in-house procedures and Level III supervisors?
: : If this is the case, our industry is in trouble.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

On Demand Webinar: Improve the Efficiency and Accuracy of Inspection Scanning

On-demand webinar on scanning technology that helps improve the efficiency and accuracy of ultrasoni
...
c inspections in oil and gas, aerospace, manufacturing and other industrial applications. The webinar features a scanning solution for multiple inspection environments, including flat and curved specimens, magnetic and nonmagnetic surfaces and raster scanning over long distances. View it today.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

Echomac® PA Tube Weld Tester

The new robotic Echomac® PA TW is an operator friendly test system for detecting weld zone defects
...
in tube and pipe caused by scarfing or welding processes. Electronic scanning ensures that the entire weld zone is covered without the need for mechanical movement or operator adjustment.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window