where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

2418 views
Technical Discussions
Hitesh Mohanlal
Hitesh Mohanlal
02:33 Dec-27-2007
Queries on Ultrasonic Testing

Dear Friends,

I have two queries as below and would really appreciate some detailed feedback, which would be helpful to us.

(1) A FBH reflects reflects differently to a logitudinally drilled hole. In Automated Bar Testing (Forge Quality Bar Stock/Bearing Quality Steels etc), we use axially drilled holes to judge the dynamic capability of the ultrasonic testing systems. The fault size in FBH is reached by increasing the testing sensitivity by a calculated factor. How is this factor arrived at? How should we co-relate that a particular size FBH reflection will be equivalent to so & so size of drill hole?

(2) Can anyone share with us the data or standards information about class AA MIL STD-2154 which is 2/64” FBDH. This is used for aircraft double Vac Arc quality. Does this standard call for manual test or automated testing?

Thanks in advance and wishes for a happy holiday season & a great New Year ahead !

Best Regards
Hitesh Mohanlal


 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1304

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1304
00:42 Dec-27-2007
Re: Queries on Ultrasonic Testing
I do not have a copy of the MIL standard 2154 so cannot speak to that item.
However, equivalent responses have been reasonably well explained by Prof. I.N. Ermolov. You can go to the article at http://www.ndt.net/article/v07n01/ginzel/ginzel.htm where you will find a utility to compare how a FBH compares to a SDH.


----------- Start Original Message -----------
: Dear Friends,
: I have two queries as below and would really appreciate some detailed feedback, which would be helpful to us.
: (1) A FBH reflects reflects differently to a logitudinally drilled hole. In Automated Bar Testing (Forge Quality Bar Stock/Bearing Quality Steels etc), we use axially drilled holes to judge the dynamic capability of the ultrasonic testing systems. The fault size in FBH is reached by increasing the testing sensitivity by a calculated factor. How is this factor arrived at? How should we co-relate that a particular size FBH reflection will be equivalent to so & so size of drill hole?
: (2) Can anyone share with us the data or standards information about class AA MIL STD-2154 which is 2/64” FBDH. This is used for aircraft double Vac Arc quality. Does this standard call for manual test or automated testing?
: Thanks in advance and wishes for a happy holiday season & a great New Year ahead !
: Best Regards
: Hitesh Mohanlal
------------ End Original Message ------------




 
 Reply 
 
Boiangiu Valentin
Boiangiu Valentin
03:34 Jan-05-2008
Re: Queries on Ultrasonic Testing

Please check the KTA references from http://www.kta-gs.de/e/standards/3200/3201_1e.pdf annex B2.3 b) for the conversion of side drilled hole(Dz) to circular disk reflector (Dksr) used for manual examinations.

The MIL STD-2154 is now cancelled and replaced with ASTM 2375. Please check http://69.7.224.88/viewnews.aspx?newsID=990

Best regards
Valentin

----------- Start Original Message -----------
: Dear Friends,
: I have two queries as below and would really appreciate some detailed feedback, which would be helpful to us.
: (1) A FBH reflects reflects differently to a logitudinally drilled hole. In Automated Bar Testing (Forge Quality Bar Stock/Bearing Quality Steels etc), we use axially drilled holes to judge the dynamic capability of the ultrasonic testing systems. The fault size in FBH is reached by increasing the testing sensitivity by a calculated factor. How is this factor arrived at? How should we co-relate that a particular size FBH reflection will be equivalent to so & so size of drill hole?
: (2) Can anyone share with us the data or standards information about class AA MIL STD-2154 which is 2/64” FBDH. This is used for aircraft double Vac Arc quality. Does this standard call for manual test or automated testing?
: Thanks in advance and wishes for a happy holiday season & a great New Year ahead !
: Best Regards
: Hitesh Mohanlal
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

Customized Probes and Transducers

With a strong development department and our own piezocomposite production, we accompany you from th
...
e first product idea to serial production. Our scientists are continuously researching new methods in the field of ultrasonic measurement technology. The progress achieved enables us to offer you optimal solutions.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window