where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
451 views
Technical Discussions
Jason
Jason
08:32 Feb-18-2008
Can magnetic force influence to the propagation of the ultrasound?

I am planning to set up both the UT and MPI test mashies.
Test piece is billet with 10m longs.
Because of limitation of space UT systems will be adjacent to MPI systems
During the Ultrasonic machine inspect the tail of the billet; MPI machine will magnetize the front of the billet.
So Ultrasound will propagate into the billet during magnetizer unit of MPI systems magnetizing the billet by yoke method.
In this case, magnetic forces influence the propagation of ultrasound?
If we can ignore this influence. My 1st question is OK.
Then how about the noise signal causing the MPI systems?
Is it OK ?
We will apply the yoke method for magnetization and water gap method for the coupling between the billet and probe for UT inspection task.
I think some noise signal from MPI system can go into the receiver along the surface of wet billet.

I would like to collect the positive idea of engineering specialist in NDT systems. Any of idea is helpful for me. Please let me know your idea.



 
 Reply 
 
John Brunk
Engineering, NDT Level III
Self employed, part-time, USA, Joined Oct 1999, 161

John Brunk

Engineering, NDT Level III
Self employed, part-time,
USA,
Joined Oct 1999
161
09:15 Feb-18-2008
Re: Can magnetic force influence to the propagation of the ultrasound?
It is unlikely that a changing magnetic field in the billet will influence propagation of ultraound in the material. Unfortunately, it is very likely that airborne RF will be picked up by the transducer cables acting as an antenna, giving you strange signals. You should consider using very well shielded cables and moving the utraonic instrument some distance away from the magnetizing equipment. How far away can be determined by trial and error.

John Brunk -
---------- Start Original Message -----------
: I am planning to set up both the UT and MPI test mashies.
: Test piece is billet with 10m longs.
: Because of limitation of space UT systems will be adjacent to MPI systems
: During the Ultrasonic machine inspect the tail of the billet; MPI machine will magnetize the front of the billet.
: So Ultrasound will propagate into the billet during magnetizer unit of MPI systems magnetizing the billet by yoke method.
: In this case, magnetic forces influence the propagation of ultrasound?
: If we can ignore this influence. My 1st question is OK.
: Then how about the noise signal causing the MPI systems?
: Is it OK ?
: We will apply the yoke method for magnetization and water gap method for the coupling between the billet and probe for UT inspection task.
: I think some noise signal from MPI system can go into the receiver along the surface of wet billet.
: I would like to collect the positive idea of engineering specialist in NDT systems. Any of idea is helpful for me. Please let me know your idea.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

Panther

M2M PANTHER is a phased-array equipment designed for both desktop and industrial applications, offer
...
ing unparalleled performance in a compact unit. It combines the speed required for industrial integrated Phased-Array Ultrasound (PAUT) solutions, with the most complete set of total focusing method (TFM) imaging techniques, making it the ultimate tool for R&D and procedure qualification.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window