where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1110 views
Technical Discussions
Dwight Whitwell
Teacher, -
Amarillo College, USA, Joined Feb 2008, 2

Dwight Whitwell

Teacher, -
Amarillo College,
USA,
Joined Feb 2008
2
03:20 Feb-15-2008
Automation/Sperry US454

Amarillo College has an Automation US454 c-scan immersion scanner which we would like to upgrade. It seems that paper for the pen recorder is hard to obtain, so we would like to record scans on a PC. Can anyone provide guidance for attaching motion encoders or potentiometers.? We could also use recommendations for PC software. For flaw detectors, we can supply Epoch 2002s with analoge gate output, or newer Krautkramer USM 58 or Panametrics units. Since this is not a corporate sponsored project, we are looking to do this upgrade ourselves, rather than purchasing a commercial solution.


 
 Reply 
 
Phil Thayer
Phil Thayer
06:53 Feb-16-2008
Re: Automation/Sperry US454
Hello Dwight, NDT-Automation has performed many full digital C-Scan upgrades on AI systems like yours. I
notice you stated you would like to do some of the upgrade yourself? We can assist you.

Phil Thayer
NDTA 609-716-4051

ndtautomation.com


----------- Start Original Message -----------
: Amarillo College has an Automation US454 c-scan immersion scanner which we would like to upgrade. It seems that paper for the pen recorder is hard to obtain, so we would like to record scans on a PC. Can anyone provide guidance for attaching motion encoders or potentiometers.? We could also use recommendations for PC software. For flaw detectors, we can supply Epoch 2002s with analoge gate output, or newer Krautkramer USM 58 or Panametrics units. Since this is not a corporate sponsored project, we are looking to do this upgrade ourselves, rather than purchasing a commercial solution.
------------ End Original Message ------------




 
 Reply 
 
Joe Buckley
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 528

Joe Buckley

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
528
03:02 Feb-18-2008
Re: Automation/Sperry US454
I would strongly recommend the Winspect software from UTEX (www.utex.com)

We have sold a few of these in the UK, and used it to upgrade an old electro sensitive paper tank of our own.


Assuming the old sperry tank uses stepper motors and the power supply / driver amplifiers (may need some work here on some older systems) are in good shape all you should need is

PC - Dual monitors recoomended

Winspect software

Motion control card - Galil or similar

A/D card - National Instruments recommended.


Any of the Flaw Detectors should work, but all will probably have a fairly slow update rate - Less of an issue if you are not doing 'production' work so can keep the speed down.

When this becomes an issue we'd happily sell you one of our Masterscan Flaw Detectors, which are much faster..

Good luck

Joe


----------- Start Original Message -----------
: Amarillo College has an Automation US454 c-scan immersion scanner which we would like to upgrade. It seems that paper for the pen recorder is hard to obtain, so we would like to record scans on a PC. Can anyone provide guidance for attaching motion encoders or potentiometers.? We could also use recommendations for PC software. For flaw detectors, we can supply Epoch 2002s with analoge gate output, or newer Krautkramer USM 58 or Panametrics units. Since this is not a corporate sponsored project, we are looking to do this upgrade ourselves, rather than purchasing a commercial solution.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window