where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1245 views
Technical Discussions
Mohammed Shafie
Mohammed Shafie
01:48 Jan-28-2000
Degassing Water

Dear Sir/Madam,
I was wondering if anyone can provide me with information
on ways to degass water. thank you
Cheers

Mohammed Shafie
McGill University
Civil Engineering Department
tel.: (514) 398-8313
fax: (514) 398-7361


 
 Reply 
 
Robert (Rocky) A. Day
Engineering
Milky Way Jewels, USA, Joined Nov 1998, 40

Robert (Rocky) A. Day

Engineering
Milky Way Jewels,
USA,
Joined Nov 1998
40
01:17 Jan-29-2000
Re: Degassing Water



 
 Reply 
 
John Rutter
John Rutter
01:45 Jan-29-2000
Re: Degassing Water
Heating (see Rocky's post) or allowing to stand for several days helps get rid of the excess air dissolved in cold tap water.

Alternately, Sonotech sells a wetting agent specifically for accelerating the offgassing of water in immersion tanks. The product name is Echowet. FWIW, it also helps couple the water to dirty or oily parts, allowing better acoustic coupling as a result.


Good luck,
John



 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1300

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1300
03:17 Jan-29-2000
Re: Degassing Water
I used to work in a facility where we used a fair bit of degassed water.
I recall filling a steel tank about 30cm diameter holding about 100 litres.
This had a flat Perspex top that fit over the top after filling (a gasket and clamps secured the Perspex that was about 3cm thick).
A Tee fitting was drilled through the Perspex and we had a water hose affixed to either side of straight branch of the Tee.
Water passed through the Tee and the Venturi effect pulled a good vacuum.
We would watch the water surface through the Perspex until the bubbles stopped and a reasonable degassing was achieved.

Ed


: Dear Sir/Madam,
: I was wondering if anyone can provide me with information
: on ways to degass water. thank you
: Cheers

: Mohammed Shafie
: McGill University
: Civil Engineering Department
: tel.: (514) 398-8313
: fax: (514) 398-7361




 
 Reply 
 
Wieslaw Bicz
Engineering,
PBP Optel sp. z o.o., Poland, Joined Feb 2009, 276

Wieslaw Bicz

Engineering,
PBP Optel sp. z o.o.,
Poland,
Joined Feb 2009
276
06:48 Jan-29-2000
Re: Degassing Water
: Dear Sir/Madam,
: I was wondering if anyone can provide me with information
: on ways to degass water. thank you
: Cheers

There is also the possibility to use ultrasonic waves with enough power to cause cavitation.
This works very quickly and very good (not only with water, but also with even very viscous fluids).

Wieslaw Bicz

http://www.optel.com.pl


 
 Reply 
 

Product Spotlight

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window