where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

VOGT Ultrasonics GmbH
non-destructive testing, services, training, ultrasonic systems, immersion and squirter inspection systems, PROline, digital radiology
1806 views
Technical Discussions
novice
novice
03:56 Apr-30-2008
shear wave test frequency and probe angle

How can I calculate the test frequency and probe angle to be used before preforming a shear wave examination?


 
 Reply 
 
Gowri Santhosh Palika
Gowri Santhosh Palika
03:36 May-01-2008
Re: shear wave test frequency and probe angle
----------- Start Original Message -----------
: How can I calculate the test frequency and probe angle to be used before preforming a shear wave examination?
------------ End Original Message ------------

Calculation of probe angle
It is depend on the thickness of job and weld geometry. There is a formula to get probe angle according to thickness ''Probe angle = 90 - T''. Here T is thickness of job. There is an another formula according to weld geometry is '' Probe angle = 90-®/2''. Here ®(tita) = groove angle. this formula is used when the job thickness is high and if therf is any necessity.
Probe frequency
It is depend on the type of job, job material, sensitivity requirements and thickness of job. There is no any formulas to calculate the probe frequency.


 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 889

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
889
00:13 May-01-2008
Re: shear wave test frequency and probe angle
----------- Start Original Message -----------
: : How can I calculate the test frequency and probe angle to be used before preforming a shear wave examination?
: Calculation of probe angle
: It is depend on the thickness of job and weld geometry. There is a formula to get probe angle according to thickness ''Probe angle = 90 - T''. Here T is thickness of job. There is an another formula according to weld geometry is '' Probe angle = 90-®/2''. Here ®(tita) = groove angle. this formula is used when the job thickness is high and if therf is any necessity.
: Probe frequency
: It is depend on the type of job, job material, sensitivity requirements and thickness of job. There is no any formulas to calculate the probe frequency.
------------ End Original Message ------------

Hi,

I totally agree, but would like to ad to that. In regards to weld inspection, very often, you don't have a choice in the frequency and probe angle. They are dictated by code. But has Gowri said, it depends on thickness and part geometry.

Secondly, to help you a little more, as a rule of thumb my buddies and I are using the following guidelines: Less than 6 inches (12 mm) we use a 5 MHz. Greater than 6 we use 2.25 MHz. The other rules of thumb we go by is if the art is greater than 3 inches (6 mm) in thickness we use a 1 inch (25 mm) diameter probe.

Hope this is helping

Michel




 
 Reply 
 

Product Spotlight

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

New PHAsis module for longitudinal weld seam inspection

PHAsis® Phased Array manual ultrasonic spot weld inspection device is now ideally suited for test
...
ing of longitudinally welded seams (e.g. Arplas® seam, short line seams) with a length of 3 to 12 mm.
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

GEKKO, Standard and Advanced phased-array for Easier inspection

M2M Gekko® is a field-proven flaw detector offering PAUT, UT, TOFD and TFM through the streamline
...
d user interface Capture™. Released in 32:128, 64:64 or 64:128 channel configurations, Gekko combines high- resolution and speed while reducing inspectors’ training time.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window