where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1239 views
Technical Discussions
felix
felix
09:47 May-17-2008
reference selection

how can i define the selection of a reference standard in an automatic ut inspection of steel pipes. can i use to inspect a pipe with one heat treatment one with double treatment? can i use as reference a pipe with a steel grade diferent if the pipe to inspect have the same heat treatment? how much will affect a heat treatment diferent to the acoustic properties in a steel pipe? thanks for your help.


 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 897

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
897
02:47 May-19-2008
Re: reference selection
Hi Felix,

Before I can tell you how to select a reference standard, you must remember what NDT is all about. It the practice of evaluating a part or piece of material without impairing its future usefulness. To do this, you compare a known (your reference standard) with an unkwon (the part being inspected).

From this first part of my answer, it goes without saying that any reference standard should be as close to the real thing as possible. Sometimes, you may get away with a 1018 steel IIW Block and inspect 4030 steel. The difference will be little, but the best thing if you can, should be a reference standard that is a true representaiton of the part being inspected. Also, if you read different Codes and Specifications, they will spedify that you should get a Reference Standard made up of the same material, heat treatment, surface finish and dimensions as what you will be inspecting.

Also not mentionned too often, have your Reference Standard and the part being tested at the same temperature.Temperature does affect material velocity.

Hope this will help you.

Michel

----------- Start Original Message -----------
: how can i define the selection of a reference standard in an automatic ut inspection of steel pipes. can i use to inspect a pipe with one heat treatment one with double treatment? can i use as reference a pipe with a steel grade diferent if the pipe to inspect have the same heat treatment? how much will affect a heat treatment diferent to the acoustic properties in a steel pipe? thanks for your help.
------------ End Original Message ------------




 
 Reply 
 
felix
felix
03:33 May-19-2008
Re: reference selection
thanks a lot Michel, about the codes and specifications, could you tell me wich one speak about the heat treatment and surface conditions....

regards, felix.


----------- Start Original Message -----------
: Hi Felix,
: Before I can tell you how to select a reference standard, you must remember what NDT is all about. It the practice of evaluating a part or piece of material without impairing its future usefulness. To do this, you compare a known (your reference standard) with an unkwon (the part being inspected).
: From this first part of my answer, it goes without saying that any reference standard should be as close to the real thing as possible. Sometimes, you may get away with a 1018 steel IIW Block and inspect 4030 steel. The difference will be little, but the best thing if you can, should be a reference standard that is a true representaiton of the part being inspected. Also, if you read different Codes and Specifications, they will spedify that you should get a Reference Standard made up of the same material, heat treatment, surface finish and dimensions as what you will be inspecting.
: Also not mentionned too often, have your Reference Standard and the part being tested at the same temperature. Temperature does affect material velocity.
: Hope this will help you.
: Michel
: : how can i define the selection of a reference standard in an automatic ut inspection of steel pipes. can i use to inspect a pipe with one heat treatment one with double treatment? can i use as reference a pipe with a steel grade diferent if the pipe to inspect have the same heat treatment? how much will affect a heat treatment diferent to the acoustic properties in a steel pipe? thanks for your help.
------------ End Original Message ------------




 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 897

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
897
02:38 May-19-2008
Re: reference selection
Presently 2 Codes that I'm working to are ASTM A418-05 and ASTM A388-07. They both deals with Steel Forgings. For A388 paragraph 7 tell you of the Forging Preparation while in A418 it is paragraph 4.2

One thing that I also forgot to mention and we do omit to do is that when we calibrate our set up should be the same as what we re inspecting. I've seen guys calibrating for weld inspection horizontally while the weld they will be inspecting is vertical. Just the fact that your couplant will be running off during the inspection (and not during your calibration) is enough to change your result. With a change in couplant thickness you may loose as much as 5 dB!!!

Food for taught!!!
Michel
----------- Start Original Message -----------
: thanks a lot Michel, about the codes and specifications, could you tell me wich one speak about the heat treatment and surface conditions....
: regards, felix.
:
: : Hi Felix,
: : Before I can tell you how to select a reference standard, you must remember what NDT is all about. It the practice of evaluating a part or piece of material without impairing its future usefulness. To do this, you compare a known (your reference standard) with an unkwon (the part being inspected).
: : From this first part of my answer, it goes without saying that any reference standard should be as close to the real thing as possible. Sometimes, you may get away with a 1018 steel IIW Block and inspect 4030 steel. The difference will be little, but the best thing if you can, should be a reference standard that is a true representaiton of the part being inspected. Also, if you read different Codes and Specifications, they will spedify that you should get a Reference Standard made up of the same material, heat treatment, surface finish and dimensions as what you will be inspecting.
: : Also not mentionned too often, have your Reference Standard and the part being tested at the same temperature. Temperature does affect material velocity.
: : Hope this will help you.
: : Michel
: : : how can i define the selection of a reference standard in an automatic ut inspection of steel pipes. can i use to inspect a pipe with one heat treatment one with double treatment? can i use as reference a pipe with a steel grade diferent if the pipe to inspect have the same heat treatment? how much will affect a heat treatment diferent to the acoustic properties in a steel pipe? thanks for your help.
------------ End Original Message ------------




 
 Reply 
 
tj
tj
01:21 May-28-2008
Re: reference selection
----------- Start Original Message -----------
: how can i define the selection of a reference standard in an automatic ut inspection of steel pipes. can i use to inspect a pipe with one heat treatment one with double treatment? can i use as reference a pipe with a steel grade diferent if the pipe to inspect have the same heat treatment? how much will affect a heat treatment diferent to the acoustic properties in a steel pipe? thanks for your help.
------------ End Original Message ------------

The reference standard should be defined in the code you are inspecting to or by customer request (if applicable). If ASME is used, the standard will be defined per procedure. The norm is for the reference to be the same material and heat treatment as part to be inspected. The heat treatment difference between specimens will have an effect on test results.Hope it helps!



 
 Reply 
 

Product Spotlight

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

VeeScan AirCraft Wheel Inspection

The VEESCAN offers maximum flexibility, has a proven mechanical design and records of breakdown-fr
...
ee operation of over 365 days. Appealing to companies in the Aerospace industry, the VEESCAN is ideal for all wheel-testing environments. With a wide selection of probes, the VeeScan allows your wheel testing facility the flexibility to select the most compatible configurations with their workload.
>

MANTIS

MANTIS is a compact, powerful and affordable flaw detector (16:64PR), dedicated to field operators
...
. This portable equipment offers standard (electronic-, sector-, compound scan, conventional UT for pulse-echo, dual array and TOFD inspections), and advanced phased-array (real-time TFM -Total Focusing Method). MANTIS benefits from the same intuitive and user-friendly interface (CAPTURE) than Gekko for easier inspections.
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window