where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
839 views
Technical Discussions
M.C Macke
NDT Inspector
GE Inspection Services, USA, Joined Aug 2001, 8

M.C Macke

NDT Inspector
GE Inspection Services,
USA,
Joined Aug 2001
8
06:57 Mar-13-2000
Hi Temp thickness of enamle on carbon.

Without touching the piece, it is of major interest to know the
thickness of the enamle coating on cast iron. The maximum thickness
is 3mm. The key is to know this thickness at the initial
solidification temp of 1000f...if there is to little, then he can
add (t), this will help reduce the heating cycles and improve
the Quality control. This system can be assemply line driven if
proven reliable. The problems are 1000f and no contact. Emat is
out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
I don't know? Could Infrared be of some help or other optical
method? This one is giving me a hard time of it!!!!




 
 Reply 
 
M. William Moyer
M. William Moyer
07:04 Mar-13-2000
Re: Hi Temp thickness of enamle on carbon.
I saw something recently where laser ultrasonics was used to measure
wet paint thickness. Perhaps it would also work here.


: Without touching the piece, it is of major interest to know the
: thickness of the enamle coating on cast iron. The maximum thickness
: is 3mm. The key is to know this thickness at the initial
: solidification temp of 1000f...if there is to little, then he can
: add (t), this will help reduce the heating cycles and improve
: the Quality control. This system can be assemply line driven if
: proven reliable. The problems are 1000f and no contact. Emat is
: out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
: I don't know? Could Infrared be of some help or other optical
: method? This one is giving me a hard time of it!!!!




 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 610

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
610
06:47 Mar-14-2000
Re: Hi Temp thickness of enamle on carbon.
: Without touching the piece, it is of major interest to know the
: thickness of the enamle coating on cast iron. The maximum thickness
: is 3mm. The key is to know this thickness at the initial
: solidification temp of 1000f...if there is to little, then he can
: add (t), this will help reduce the heating cycles and improve
: the Quality control. This system can be assemply line driven if
: proven reliable. The problems are 1000f and no contact. Emat is
: out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
: I don't know? Could Infrared be of some help or other optical
: method? This one is giving me a hard time of it!!!!
----------------

Be carefully by measuring under such hot conditions.
You can get calibration errors of sound velocity, also
the circumferential temperature may not be equal.
There is a company 'MOOG-BUHL AUTOMATION' which supplied
ultrasonic in this field, but measured more down the line.

Rolf



 
 Reply 
 

Product Spotlight

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

GEKKO, Standard and Advanced phased-array for Easier inspection

M2M Gekko® is a field-proven flaw detector offering PAUT, UT, TOFD and TFM through the streamline
...
d user interface Capture™. Released in 32:128, 64:64 or 64:128 channel configurations, Gekko combines high- resolution and speed while reducing inspectors’ training time.
>

Echomac® Small

Available with up to eight channels of electronics to detect and evaluate thickness, flaws and eccen
...
tricity, this UT tester is housed in a convenient, smaller cabinet. This instrument can be used in conjunction with bubbler or immersion tank systems, or with a test bench or in laboratory applications. The Echomac® Small is available in the FD4, FD6 or FD6A versions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window