where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

862 views
Technical Discussions
M.C Macke
NDT Inspector
GE Inspection Services, USA, Joined Aug 2001, 8

M.C Macke

NDT Inspector
GE Inspection Services,
USA,
Joined Aug 2001
8
06:57 Mar-13-2000
Hi Temp thickness of enamle on carbon.

Without touching the piece, it is of major interest to know the
thickness of the enamle coating on cast iron. The maximum thickness
is 3mm. The key is to know this thickness at the initial
solidification temp of 1000f...if there is to little, then he can
add (t), this will help reduce the heating cycles and improve
the Quality control. This system can be assemply line driven if
proven reliable. The problems are 1000f and no contact. Emat is
out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
I don't know? Could Infrared be of some help or other optical
method? This one is giving me a hard time of it!!!!




 
 Reply 
 
M. William Moyer
M. William Moyer
07:04 Mar-13-2000
Re: Hi Temp thickness of enamle on carbon.
I saw something recently where laser ultrasonics was used to measure
wet paint thickness. Perhaps it would also work here.


: Without touching the piece, it is of major interest to know the
: thickness of the enamle coating on cast iron. The maximum thickness
: is 3mm. The key is to know this thickness at the initial
: solidification temp of 1000f...if there is to little, then he can
: add (t), this will help reduce the heating cycles and improve
: the Quality control. This system can be assemply line driven if
: proven reliable. The problems are 1000f and no contact. Emat is
: out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
: I don't know? Could Infrared be of some help or other optical
: method? This one is giving me a hard time of it!!!!




 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 617

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
617
06:47 Mar-14-2000
Re: Hi Temp thickness of enamle on carbon.
: Without touching the piece, it is of major interest to know the
: thickness of the enamle coating on cast iron. The maximum thickness
: is 3mm. The key is to know this thickness at the initial
: solidification temp of 1000f...if there is to little, then he can
: add (t), this will help reduce the heating cycles and improve
: the Quality control. This system can be assemply line driven if
: proven reliable. The problems are 1000f and no contact. Emat is
: out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
: I don't know? Could Infrared be of some help or other optical
: method? This one is giving me a hard time of it!!!!
----------------

Be carefully by measuring under such hot conditions.
You can get calibration errors of sound velocity, also
the circumferential temperature may not be equal.
There is a company 'MOOG-BUHL AUTOMATION' which supplied
ultrasonic in this field, but measured more down the line.

Rolf



 
 Reply 
 

Product Spotlight

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

AIS229 - Multipurpose Real Time System

Latest standard & automatic real time system developed by Balteau. The AIS229 has been designed to
...
do series inspection in a wide variety of industry. Composed of a shielded cabinet, 5 axis manipulator, x-ray generator and tubehead from 160kV to 225kV, a fl at panel & much more, the AIS229 is most certainly one of the most multipurpose RTR system available on the market.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window