where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

DASEL SISTEMAS
Our Phased Array equipments, based on SITAU Technology, are among the PAS highest performance in the market.
823 views
Technical Discussions
M.C Macke
NDT Inspector
GE Inspection Services, USA, Joined Aug 2001, 8

M.C Macke

NDT Inspector
GE Inspection Services,
USA,
Joined Aug 2001
8
06:57 Mar-13-2000
Hi Temp thickness of enamle on carbon.

Without touching the piece, it is of major interest to know the
thickness of the enamle coating on cast iron. The maximum thickness
is 3mm. The key is to know this thickness at the initial
solidification temp of 1000f...if there is to little, then he can
add (t), this will help reduce the heating cycles and improve
the Quality control. This system can be assemply line driven if
proven reliable. The problems are 1000f and no contact. Emat is
out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
I don't know? Could Infrared be of some help or other optical
method? This one is giving me a hard time of it!!!!




 
 Reply 
 
M. William Moyer
M. William Moyer
07:04 Mar-13-2000
Re: Hi Temp thickness of enamle on carbon.
I saw something recently where laser ultrasonics was used to measure
wet paint thickness. Perhaps it would also work here.


: Without touching the piece, it is of major interest to know the
: thickness of the enamle coating on cast iron. The maximum thickness
: is 3mm. The key is to know this thickness at the initial
: solidification temp of 1000f...if there is to little, then he can
: add (t), this will help reduce the heating cycles and improve
: the Quality control. This system can be assemply line driven if
: proven reliable. The problems are 1000f and no contact. Emat is
: out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
: I don't know? Could Infrared be of some help or other optical
: method? This one is giving me a hard time of it!!!!




 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 609

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
609
06:47 Mar-14-2000
Re: Hi Temp thickness of enamle on carbon.
: Without touching the piece, it is of major interest to know the
: thickness of the enamle coating on cast iron. The maximum thickness
: is 3mm. The key is to know this thickness at the initial
: solidification temp of 1000f...if there is to little, then he can
: add (t), this will help reduce the heating cycles and improve
: the Quality control. This system can be assemply line driven if
: proven reliable. The problems are 1000f and no contact. Emat is
: out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
: I don't know? Could Infrared be of some help or other optical
: method? This one is giving me a hard time of it!!!!
----------------

Be carefully by measuring under such hot conditions.
You can get calibration errors of sound velocity, also
the circumferential temperature may not be equal.
There is a company 'MOOG-BUHL AUTOMATION' which supplied
ultrasonic in this field, but measured more down the line.

Rolf



 
 Reply 
 

Product Spotlight

NOVO Armor 15 & NOVO Armor 22

The Armor Kit Contains the NOVO Armor, which provides additional mechanical protection to the NOVO 1
...
5WN & NOVO 22WN Detectors, the Armor Stand and a traveling soft cover. - Newest shock absorbent technology case - Water resistant design - Supports wired & wireless communication - Multiple positioning options - Tripod connection using the Built-in 1/4” threads - Simple Detector battery replacement
>

PROlineTOP Plug & Play Ultrasonic inspection device

As Plug & Play solution it units all control and operation elements in a small housing and therefo
...
re replaces the typical control cabinet...
>

A1525 SOLO

A1525 Solo – the most compact and affordable TMF unit with two phased array transducers and 3D v
...
isualization and analysis software in standard delivery set. A compact, ergonomic and easy to handheld Phased Array unit based on Total Focusing Method for easy-going imaging of inspection objects with two-dimensional and three-dimensional visualization and evaluation of inspection results.
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window